Continuing Education Session 1 - (Part 2 of 6)

Views:
 
Category: Education
     
 

Presentation Description

No description available.

Comments

Presentation Transcript

Slide 1: 

Welcome to Cape Cod Plumbing School’s 6 Hour Continuing Education Course SESSION 1! Appeal Procedure Please read the following instructions to fully understand how to take the course: To make the presentation full screen, click the square icon on the bottom right corner just outside this presentation box. To go back to a previous slide Click on this side of the screen To go to the next slide Click on this side of the screen Audio for each slide will AUTOMATICALLY PLAY And CANNOT be paused. If you need to hear it again, simply go to the next slide, then go back to the slide you wanted to hear again. Each fill in the blank question on the 2 workbooks has a page number next to it. That number corresponds to the PG # at the top right corner of each slide. Look at the PG # on the slide if you lose your place on the workbook. When you are finished with this part of the course, a final slide will display a link. Click the link to move on to the next part of the course. Fullscreen Button PG #

Slide 2: 

APPEAL PROCEDURE IF YOU DISAGREE WITH AN INSPECTOR'S DECISION a) YOU CAN NOTIFY THE STATE INSPECTOR BY PHONE OR LETTER b) THE STATE INSPECTOR CAN GATHER ALL FACTS AND RENDER A DECISION NOT FINAL APPEAL TO THE BOARD a) THE APPEAL SHALL BE IN WRITING b) ACCOMPANIED BY A CHECK FOR $75 c) PAYABLE TO THE COMMONWEALTH d) IF THE BOARD FINDS IN YOUR FAVOR YOUR CHECK MAY BE RETURNED PG. 20 3.05 6 A 1 2 3 PG. 20 3.05 B - 1 PG. 20 3.05 6 B PG 8

Slide 3: 

VARIANCE AN ALTERNATIVE METHOD, SYSTEM, OR PRODUCT THAT DOES NOT COMPLY WITH THE CODE. MUST BE AN UNUSUAL OR EXTRAORDINARY CIRCUM - STANCE OR AN ESTABLISHED HARDSHIP. PERMISSION FROM THE BOARD FOR USING AN ALTERNATIVE METHOD, SYSTEM, OR PRODUCT IS FOR ONE INSTANCE AT ONE LOCATION. NO WORK SHALL START BEFORE THE BOARD HAS APPROVED THE VARIANCE. PG. 15 3.04 2A PG. 15 3.04 2 A 1 PG. 15 3.04 2 A 2 PG. 15 3.04 2 B PG 9

Slide 4: 

VARIANCE APPLICATION a) MADE TO THE BOARD BEFORE FILING FOR THE PLUMBING PERMIT b) SHALL BE SUBMITTED IN WRITING AND USING THE FORM PROVIDED BY THE BOARD OF HEALTH c) INCLUDE A COPY OF THE PETITION FOR THE VARIANCE THAT WAS MADE TO THE BOARD OF HEALTH d) INCLUDE A COPY OF THE BOARD OF HEALTH RESPONSE TO THE PETITION FOR VARIANCE PG. 15 3.04 2 C 1 PG. 15 3.04 2 C 3 PG. 15 3.04 2 C 4 PG. 15 3.04 2 C 2 PG 10

Slide 5: 

THE APPLICANT FOR A VARIANCE SHALL a) PROVIDE A COMPLETE APPLICATION IN COMPLIANCE WITH 248 C M R b) INCLUDE A NON-REFUNDABLE FEE $75 c) THE CHECK IS MADE PAYABLE TO THE COMM. OF MASS d) APPEAR AT THE BOARD MEETING WHEN THE VARIANCE IS DISCUSSED e) FULFILL THE REQUIREMENTS ESTABLISHED BY THE BOARD PG. 15 3.04 2 D PG 11

Slide 6: 

SPECIAL PERMISSION WHEN SAFETY IS A SPECIAL CONSIDERATION A LICENSEE MAY OBTAIN SPECIAL PERMISSION FROM THE BOARD BEFORE INSTALLING OR USING A GIVEN PRODUCT, SYSTEM, DESIGN OR METHOD. TO OBTAIN SPECIAL PERMISSION AN APPLICANT SHALL: a) SUBMIT A REQUEST TO THE BOARD b) APPEAR AT THE BOARD MEETING WHEN THE REQUEST IS SCHEDULED TO BE DISCUSSED PG. 16 3.04 3 A PG. 16 3.04 3 B PG 12

Slide 7: 

SPECIAL PERMISSION REQUEST FORM $75 FEE FULLY COMPLETED APPLICATION CERTIFICATION THAT THE SYSTEM WAS DESIGNED OR ENGINEERED BY A QUALIFIED INDIVIDUAL d) A SET OF CONSTRUCTION DOCUMENTS STAMPED BY AN ENGINEER e) ANY OTHER REQUIRED DOCUMENTS PG. 16 3.04 3 C PG 13

Slide 8: 

TYPES OF SPECIAL PERMISSION REQUESTS VENTING SYSTEM BLACK WATER AIR ADMITTANCE VALVE GRAY WATER AUTOMATIC VENT SO - VENT COMBINATION WASTE & VENT WATER RECYLING SYSTEMS ONSITE WASTE WATER TREATMENT PG 14

Slide 9: 

DEVIATIONS a) EXISTING WORK b) INSPECTOR’S PERMISSION c) NECESSARY d) COMPLIES TO THE INTENT OF THE CODE RULE 21 PG. 21 PG 15

Slide 10: 

STATE INVESTIGATORS CONTACT INFORMATION: TAYLOR E. ROTH JR. (617)727-6092 DENNIS DRISCOLL (617)727-2243 SCOTT PADDEN (617)727-1738 FAX # (617)727-6092 PG 16

Slide 11: 

You have completed this part of the course. The next part is PVC & ABS. On your computer keyboard, please press the “Esc” key located at the top left corner. This will take you out of fullscreen mode. This is required if you want to continue to the next part of the course. Once you have pressed the “Esc” key and are out of fullscreen mode, please click the link below to continue: Continuing Education Session 1 - PVC & ABS

authorStream Live Help