logging in or signing up 8085 vishesh_0802 Download Post to : URL : Related Presentations : Share Add to Flag Embed Email Send to Blogs and Networks Add to Channel Uploaded from authorPOINT lite Insert YouTube videos in PowerPont slides with aS Desktop Copy embed code: Embed: Flash iPad Dynamic Copy Does not support media & animations Automatically changes to Flash or non-Flash embed WordPress Embed Customize Embed URL: Copy Thumbnail: Copy The presentation is successfully added In Your Favorites. Views: 10156 Category: Entertainment License: All Rights Reserved Like it (7) Dislike it (0) Added: September 10, 2009 This Presentation is Public Favorites: 2 Presentation Description No description available. Comments Posting comment... Premium member Presentation Transcript The 8085 Microprocessor Architecture : The 8085 Microprocessor Architecture www.yesnaraynan.blogspot.com The 8085 and Its Busses : The 8085 and Its Busses The 8085 is an 8-bit general purpose microprocessor that can address 64K Byte of memory. It has 40 pins and uses +5V for power. It can run at a maximum frequency of 3 MHz. The pins on the chip can be grouped into 6 groups: Address Bus. Data Bus. Control and Status Signals. Power supply and frequency. Externally Initiated Signals. Serial I/O ports. www.yesnarayanan.blogspot.com The Address and Data Busses : The Address and Data Busses The address bus has 8 signal lines A8 – A15 which are unidirectional. The other 8 address bits are multiplexed (time shared) with the 8 data bits. So, the bits AD0 – AD7 are bi-directional and serve as A0 – A7 and D0 – D7 at the same time. During the execution of the instruction, these lines carry the address bits during the early part, then during the late parts of the execution, they carry the 8 data bits. In order to separate the address from the data, we can use a latch to save the value before the function of the bits changes. www.yesnarayanan.blogspot.com The Control and Status Signals : The Control and Status Signals There are 4 main control and status signals. These are: ALE: Address Latch Enable. This signal is a pulse that become 1 when the AD0 – AD7 lines have an address on them. It becomes 0 after that. This signal can be used to enable a latch to save the address bits from the AD lines. RD: Read. Active low. WR: Write. Active low. IO/M: This signal specifies whether the operation is a memory operation (IO/M=0) or an I/O operation (IO/M=1). S1 and S0 : Status signals to specify the kind of operation being performed .Usually un-used in small systems. www.yesnarayanan.blogspot.com Frequency Control Signals : Frequency Control Signals There are 3 important pins in the frequency control group. X0 and X1 are the inputs from the crystal or clock generating circuit. The frequency is internally divided by 2. So, to run the microprocessor at 3 MHz, a clock running at 6 MHz should be connected to the X0 and X1 pins. CLK (OUT): An output clock pin to drive the clock of the rest of the system. We will discuss the rest of the control signals as we get to them. www.yesnarayanan.blogspot.com Microprocessor Communication and Bus Timing : Microprocessor Communication and Bus Timing To understand how the microprocessor operates and uses these different signals, we should study the process of communication between the microprocessor and memory during a memory read or write operation. Lets look at timing and the data flow of an instruction fetch operation. (Example 3.1) www.yesnarayanan.blogspot.com Steps For Fetching an Instruction : Steps For Fetching an Instruction Lets assume that we are trying to fetch the instruction at memory location 2005. That means that the program counter is now set to that value. The following is the sequence of operations: The program counter places the address value on the address bus and the controller issues a RD signal. The memory’s address decoder gets the value and determines which memory location is being accessed. The value in the memory location is placed on the data bus. The value on the data bus is read into the instruction decoder inside the microprocessor. After decoding the instruction, the control unit issues the proper control signals to perform the operation. www.yesnarayanan.blogspot.com Timing Signals For Fetching an Instruction : Timing Signals For Fetching an Instruction Now, lets look at the exact timing of this sequence of events as that is extremely important. (figure 3.3) At T1 , the high order 8 address bits (20H) are placed on the address lines A8 – A15 and the low order bits are placed on AD7–AD0. The ALE signal goes high to indicate that AD0 – AD8 are carrying an address. At exactly the same time, the IO/M signal goes low to indicate a memory operation. At the beginning of the T2 cycle, the low order 8 address bits are removed from AD7– AD0 and the controller sends the Read (RD) signal to the memory. The signal remains low (active) for two clock periods to allow for slow devices. During T2 , memory places the data from the memory location on the lines AD7– AD0 . During T3 the RD signal is Disabled (goes high). This turns off the output Tri-state buffers in the memory. That makes the AD7– AD0 lines go to high impedence mode. www.yesnarayanan.blogspot.com Demultiplexing AD7-AD0 : Demultiplexing AD7-AD0 From the above description, it becomes obvious that the AD7– AD0 lines are serving a dual purpose and that they need to be demultiplexed to get all the information. The high order bits of the address remain on the bus for three clock periods. However, the low order bits remain for only one clock period and they would be lost if they are not saved externally. Also, notice that the low order bits of the address disappear when they are needed most. To make sure we have the entire address for the full three clock cycles, we will use an external latch to save the value of AD7– AD0 when it is carrying the address bits. We use the ALE signal to enable this latch. www.yesnarayanan.blogspot.com Demultiplexing AD7-AD0 : Demultiplexing AD7-AD0 Given that ALE operates as a pulse during T1, we will be able to latch the address. Then when ALE goes low, the address is saved and the AD7– AD0 lines can be used for their purpose as the bi-directional data lines. A15-A8 Latch AD7-AD0 D7- D0 A7- A0 8085 ALE www.yesnarayanan.blogspot.com Cycles and States : Cycles and States From the above discussion, we can define terms that will become handy later on: T- State: One subdivision of an operation. A T-state lasts for one clock period. An instruction’s execution length is usually measured in a number of T-states. (clock cycles). Machine Cycle: The time required to complete one operation of accessing memory, I/O, or acknowledging an external request. This cycle may consist of 3 to 6 T-states. Instruction Cycle: The time required to complete the execution of an instruction. In the 8085, an instruction cycle may consist of 1 to 6 machine cycles. www.yesnarayanan.blogspot.com Generating Control Signals : Generating Control Signals The 8085 generates a single RD signal. However, the signal needs to be used with both memory and I/O. So, it must be combined with the IO/M signal to generate different control signals for the memory and I/O. Keeping in mind the operation of the IO/M signal we can use the following circuitry to generate the right set of signals: www.yesnarayanan.blogspot.com A closer look at the 8085 Architecture : A closer look at the 8085 Architecture Previously we discussed the 8085 from a programmer’s perspective. Now, lets look at some of its features with more detail. www.yesnarayanan.blogspot.com The ALU : The ALU In addition to the arithmetic & logic circuits, the ALU includes the accumulator, which is part of every arithmetic & logic operation. Also, the ALU includes a temporary register used for holding data temporarily during the execution of the operation. This temporary register is not accessible by the programmer. www.yesnarayanan.blogspot.com The Flags register : The Flags register There is also the flags register whose bits are affected by the arithmetic & logic operations. S-sign flag The sign flag is set if bit D7 of the accumulator is set after an arithmetic or logic operation. Z-zero flag Set if the result of the ALU operation is 0. Otherwise is reset. This flag is affected by operations on the accumulator as well as other registers. (DCR B). AC-Auxiliary Carry This flag is set when a carry is generated from bit D3 and passed to D4 . This flag is used only internally for BCD operations. (Section 10.5 describes BCD addition including the DAA instruction). P-Parity flag After an ALU operation if the result has an even # of 1’s the p-flag is set. Otherwise it is cleared. So, the flag can be used to indicate even parity. CY-carry flag Discussed earlier www.yesnarayanan.blogspot.com More on the 8085 machine cycles : More on the 8085 machine cycles The 8085 executes several types of instructions with each requiring a different number of operations of different types. However, the operations can be grouped into a small set. The three main types are: Memory Read and Write. I/O Read and Write. Request Acknowledge. These can be further divided into various operations (machine cycles). www.yesnarayanan.blogspot.com Opcode Fetch Machine Cycle : Opcode Fetch Machine Cycle The first step of executing any instruction is the Opcode fetch cycle. In this cycle, the microprocessor brings in the instruction’s Opcode from memory. To differentiate this machine cycle from the very similar “memory read” cycle, the control & status signals are set as follows: IO/M=0, s0 and s1 are both 1. This machine cycle has four T-states. The 8085 uses the first 3 T-states to fetch the opcode. T4 is used to decode and execute it. It is also possible for an instruction to have 6 T-states in an opcode fetch machine cycle. www.yesnarayanan.blogspot.com Memory Read Machine Cycle : Memory Read Machine Cycle The memory read machine cycle is exactly the same as the opcode fetch except: It only has 3 T-states The s0 signal is set to 0 instead. www.yesnarayanan.blogspot.com The Memory Read Machine Cycle : The Memory Read Machine Cycle To understand the memory read machine cycle, let’s study the execution of the following instruction: MVI A, 32 In memory, this instruction looks like: The first byte 3EH represents the opcode for loading a byte into the accumulator (MVI A), the second byte is the data to be loaded. The 8085 needs to read these two bytes from memory before it can execute the instruction. Therefore, it will need at least two machine cycles. The first machine cycle is the opcode fetch discussed earlier. The second machine cycle is the Memory Read Cycle. Figure 3.10 page 83. 2000H 2001H 3E 32 www.yesnarayanan.blogspot.com Machine Cycles vs. Number of bytes in the instruction : Machine Cycles vs. Number of bytes in the instruction Machine cycles and instruction length, do not have a direct relationship. To illustrate lets look at the machine cycles needed to execute the following instruction. STA 2065H This is a 3-byte instruction requiring 4 machine cycles and 13 T-states. The machine code will be stored in memory as shown to the right This instruction requires the following 4 machine cycles: Opcode fetch to fetch the opcode (32H) from location 2010H, decode it and determine that 2 more bytes are needed (4 T-states). Memory read to read the low order byte of the address (65H) (3 T-states). Memory read to read the high order byte of the address (20H) (3 T-states). A memory write to write the contents of the accumulator into the memory location. 2010H 2011H 2012H 32H 65H 20H www.yesnarayanan.blogspot.com The Memory Write Operation : The Memory Write Operation In a memory write operation: The 8085 places the address (2065H) on the address bus Identifies the operation as a memory write (IO/M=0, s1=0, s0=1). Places the contents of the accumulator on the data bus and asserts the signal WR. During the last T-state, the contents of the data bus are saved into the memory location. www.yesnarayanan.blogspot.com Memory interfacing : Memory interfacing There needs to be a lot of interaction between the microprocessor and the memory for the exchange of information during program execution. Memory has its requirements on control signals and their timing. The microprocessor has its requirements as well. The interfacing operation is simply the matching of these requirements. www.yesnarayanan.blogspot.com Memory structure & its requirements : Memory structure & its requirements The process of interfacing the above two chips is the same. However, the ROM does not have a WR signal. ROM www.yesnarayanan.blogspot.com Interfacing Memory : Interfacing Memory Accessing memory can be summarized into the following three steps: Select the chip. Identify the memory register. Enable the appropriate buffer. Translating this to microprocessor domain: The microprocessor places a 16-bit address on the address bus. Part of the address bus will select the chip and the other part will go through the address decoder to select the register. The signals IO/M and RD combined indicate that a memory read operation is in progress. The MEMR signal can be used to enable the RD line on the memory chip. www.yesnarayanan.blogspot.com Address decoding : Address decoding The result of address decoding is the identification of a register for a given address. A large part of the address bus is usually connected directly to the address inputs of the memory chip. This portion is decoded internally within the chip. What concerns us is the other part that must be decoded externally to select the chip. This can be done either using logic gates or a decoder. www.yesnarayanan.blogspot.com The Overall Picture : The Overall Picture Putting all of the concepts together, we get: www.yesnarayanan.blogspot.com You do not have the permission to view this presentation. In order to view it, please contact the author of the presentation.