How to Install the Engine Block Heater in your Car

Views:
 
Category: Others/ Misc
     
 

Presentation Description

The engine block heater is used to reduce the stress on the engine of your car in cold weather conditions. They help to keep the coolant warm for easy movement in the engine. You can easily install a heater in the car by following the steps like jack up the car, drain the engine, and route the power cord. In order to know more details on how to install the engine block heater in your car, see the following slides.

Comments

Presentation Transcript

PowerPoint 演示文稿:

How to Install the Engine Block Heater in your Car

PowerPoint 演示文稿:

The engine block heater of your car are used to reduce the stress on your engine during the cold weather.

PowerPoint 演示文稿:

The heater warms up the oil or coolant of the engine and makes them much easier to start a cold engine. It can improve the fuel economy in winter.

PowerPoint 演示文稿:

Thus, the electric heaters of your car allows the engine to reach their desired temperature much more quickly.

PowerPoint 演示文稿:

Several kinds of engine heater are available in the market, that will depend on the make and model of the car and its mechanical abilities.

PowerPoint 演示文稿:

Here consider the installation procedures of engine block heater to start your car in cold weather.

PowerPoint 演示文稿:

Jack up the car

PowerPoint 演示文稿:

The warm engine of your car make it slightly easier to remove the drain plugs if they are made from different metals than the engine block.

PowerPoint 演示文稿:

If you want to handle a cold car then it will protect you from burning. So, choose the one that you are comfortable with.

PowerPoint 演示文稿:

So select the one that meets your needs and compatible with the car. Then jack up the front end of the car and remove the plastic engine covers.

PowerPoint 演示文稿:

Drain engine

PowerPoint 演示文稿:

You can refer your owner's manual for getting the specific instructions about the equipment required for installing the engine block heater.

PowerPoint 演示文稿:

Remove the clips that can hold the radiator cover and the bolts that can hold the radiator mounting bracket.

PowerPoint 演示文稿:

Slide a pan under the engine and pull out the specified drain plug at the end of the engine block. Then remove the radiator cap to accelerate drainage.

PowerPoint 演示文稿:

Plug in heater

PowerPoint 演示文稿:

Pre-fit the connections between the heating rods and the power cords. Then drop the male end of the cord into the engine department.

PowerPoint 演示文稿:

Pre-fit the connections between the heating rods and the power cords. Then drop the male end of the cord into the engine department.

PowerPoint 演示文稿:

If the trapped air is present resistance, then displace it with more grease. Thus, the metal clip should be facing the rear of the car.

PowerPoint 演示文稿:

Route the power cord

PowerPoint 演示文稿:

At last plug the cord into the rod, then run the wire harness through the engine compartments just out of the front grill.

PowerPoint 演示文稿:

Don't move the car parts or the hoses and follow the included direction for improvising the installation process.

PowerPoint 演示文稿:

Once you place the cord in the correct position, secure it with wire ties. To keep the cord of the engine manifold doesn't leave the slack behind the first tie.

PowerPoint 演示文稿:

Conclusion

PowerPoint 演示文稿:

By following the above-mentioned points, you can easily install the engine block heater of your car.

PowerPoint 演示文稿:

Now you have a car that will provide more fuel efficient in cold weathers.

PowerPoint 演示文稿:

THANK YOU! https://sbautowerks.com/ https://twitter.com/hashtag/SantaBarbaraAutoRepair?src=hash https://www.facebook.com/Santa-Barbara-Autowerks-Inc-455768191174331/ https://www.instagram.com/sbautowerks/

authorStream Live Help