hmt training report

Views:
 
     
 

Presentation Description

No description available.

Comments

Presentation Transcript

SIX WEEK TRAINING REPORT AT HMT (PINJORE):

SIX WEEK TRAINING REPORT AT HMT (PINJORE) SUBMITTED BY:- Pankaj kumar Guru nank institute of technology , ambala , haryana . 6309342

Hmt is a public sector government of India undertaking company.:

Hmt is a public sector government of India undertaking company. Unit Chief :- Shri Prakash Sharan (E.D) Executive director

Organization chart :

Organization chart 1. Executive director (ED) 2. General manager (GM) 3. Joint general manager (JGM) 4. Deputy general manager (DGM) 5. Assistant General Manager 6. Manager 7. Deputy Manager 8. Foreman 9. Supervisor

DGM (Deputy General Manager Mr. V.K Grover :

DGM (Deputy General Manager Mr. V.K Grover The industrial training of six week in HMT is done under the guidance of DGM Mr. V.K Grover.

TRACTOR REAR PARTS :

TRACTOR REAR PARTS

HMT TRACTOR :

HMT TRACTOR

VARIOUS MODELS OF HMT TRACTOR:

VARIOUS MODELS OF HMT TRACTOR 6522 5911 3522 FX 3022 EDI 2522 FX 4022 4922 EDI 2511 4922 DX 5022 RX 7511 4511

HMT established Tractor Plant in Pinjore in 1971 to provide impetus to the Country’s Green Revolution:

HMT established Tractor Plant in Pinjore in 1971 to provide impetus to the Country’s Green Revolution In 1953, Hindustan Machine Tools started a single factory to produce lathes a Bangalore in collaboration with M/s Oerlikon of Switzerland. The Pinjore unit was established as the third machine  tool factory. It went into production  on 1 st OCT 1963. HMT was incorporated in 1953 by the government of India as the machine tool manufacturing company.

PRODUCTS OF HMT::

PRODUCTS OF HMT :

FOUNDRY SHOP:

FOUNDRY SHOP IT IS THE MOTHER OF INDUSTRY.

FOUNDRY SHOP : :

FOUNDRY SHOP : In India, the first cupola unit installed in pinjore hmt foundry shop. There is well-equipped and modernized foundry running in HMT. There are 3  electric furnaces working in the foundry. All the requirements of tractor division and machine tool division are fulfilled by this foundry. Casting is the final product of the foundry. Liquid metal is poured into mould and the molten metal takes the shape of the cavity.

CHARGE COMPOSITION AND CHEMISTRY:

CHARGE COMPOSITION AND CHEMISTRY CHARGE Pig iron 10-15% steel scrap 25-30% H scrap balance

Composition:

Composition GREEN SAND:- Return sand 85% New Sand 12% Betonite 2% Saw dust 1% Moisture 4-5%

TRACTOR ASS’Y:

TRACTOR ASS’Y GEAR BOX SUB ASS’Y M.T.H & GEAR BOX JOINING MECHANICAL BRAKE ASS’Y GEAR SHIFTING ASS’Y PORTAL/ DIRECT AXLE MOUNTING LIFT MOUNTING ENGINE MOUNTING STEERING ASSEMBLY

ENGINE SHOP:

ENGINE SHOP Crankshaft pre ass’y Piston pre ass’y Crankshaft ass’y Lubrication plug & punching. Gear fitting Piston mounting Lubrication pump ass’y Front & rear cover ass’y Fly wheel ass’y

Engine shop:

Engine shop Cylinder head mounting Water pump & filter ass’y Rocker arm ass’y Injection pump timing IP engine ass’y

Crankshaft:

Crankshaft

Crank case assembly:

Crank case assembly First the crank case is fitted in equilibrium. Then journal bearing is fitted. After that crankshaft is fitted. Oil cap is fitted from both sides. Then IPD (Injection pump drive) shaft is fitted. Cam shaft Lubricating pump Lubricating oil filter Pistons and connecting rods are fitted

Crank case assembly:

Crank case assembly Ring compressor is being used to push the piston inside the cylinder. Air breezer is fitted beside the IPD Shaft.

Cylinder Head:

Cylinder Head

Timing Gear Setting:

Timing Gear Setting

Types of HMT CNC are employed:

Types of HMT CNC are employed HTC 500 HMC 500S HSM 500 SNC H CNC G1100 WS1 CNC 3A VTC 1200 HTC 630

THANK YOU if there is any query plz mail at: roy.pankaj23@gmail.com :

THANK YOU if there is any query plz mail at: roy.pankaj23@gmail.com

authorStream Live Help