# Problem-Pizza_Cutter_Parts

Views:

Category: Education

## Presentation Description

No description available.

## Presentation Transcript

### PowerPoint Presentation:

OBJECTIVE: is to apply all of the skills you should’ve learned by this point . Problem # 17: Pizza Cutter (100 pts)

### Settings:

Settings New, English, Standard (in).IPT NOTE: You will make 6 parts so that we can create the Pizza Cutter. All will have the same settings! Snap = .0625 Grid = 1 & 10

### Part 1 = Guard:

Part 1 = Guard Create a New Folder & call it “Pizza Cutter” Save all of the parts you create to this folder!

### Draw to match this, keep it centered!:

Draw to match this, keep it centered!

### Modify w/2 Fillet (0.3 R):

Modify w/2 Fillet (0.3 R)

Offset it 0.042

### Draw line on both ends to finish it:

Draw line on both ends to finish it

### Extrude it 1” (centered .5 each direction):

Extrude it 1” (centered .5 each direction)

### Draw a circle w/0.400 DIA (making sure it is perfectly centered):

Draw a circle w/0.400 DIA (making sure it is perfectly centered)

### Create a 0.400 DIA hole through all:

Create a 0.400 DIA hole through all

### Now create a 3D Fillet on the 4 corners with 0.35 R:

Now create a 3D Fillet on the 4 corners with 0.35 R

### Change the material to = Metal-Steel (Stainless, Brushed) Then Save As; to the Pizza Cutter Folder; Title= Guard:

Change the material to = Metal-Steel (Stainless, Brushed) Then Save As; to the Pizza Cutter Folder; Title= Guard

### Part 2-Arm Draw it centered to match:

Part 2-Arm Draw it centered to match

### Draw rest to match:

Draw rest to match

### Offset the drawing 0.048 & draw lines to finish it at the ends:

Offset the drawing 0.048 & draw lines to finish it at the ends

### Extrude it 0.25 both ways so that it is centered:

Extrude it 0.25 both ways so that it is centered

### 3D Fillet @ 0.075 the 8 edges (this is so it better matches the look of sheet metal that has been bent):

3D Fillet @ 0.075 the 8 edges (this is so it better matches the look of sheet metal that has been bent)

### Should look like this::

Should look like this:

### Create 0.20 Fillet for the two edges of the Right side ONLY!:

Create 0.20 Fillet for the two edges of the Right side ONLY!

### Should look like this::

Should look like this:

### Rotate it so that you can see the Left side; Create a chamfer on the edges with Distance = 0.1 & Angle = 45:

Rotate it so that you can see the Left side; Create a chamfer on the edges with Distance = 0.1 & Angle = 45

### Should look like this::

Should look like this:

### Create New Sketch to match:

Create New Sketch to match

### Put a hole through it to match::

Put a hole through it to match:

### Save As::

Save As: Now save this to the Pizza Cutter Folder 17B-Arm

### Part 3-Blade Draw 2 circles (Dia= 3.5 & 0.17):

Part 3-Blade Draw 2 circles ( Dia = 3.5 & 0.17)

### Extrude it 0.50 both ways so that it is centered:

Extrude it 0.50 both ways so that it is centered

### Create a 2 direction chamfer D1=0.02 D2=0.12:

Create a 2 direction chamfer D1=0.02 D2=0.12

### Add this Chamfer to both side:

Add this Chamfer to both side

### Change the depth of the Extrusion to 0.04:

Change the depth of the Extrusion to 0.04

### Change the Material to Aluminum (Polished) & Save It:

Change the Material to Aluminum (Polished) & Save It

### Part 4-Finished Cap Draw 2 Circles; DIA = 0.98 & 1.25:

Part 4-Finished Cap Draw 2 Circles; DIA = 0.98 & 1.25

### Extrude it 0.375 both ways so that it is centered:

Extrude it 0.375 both ways so that it is centered

### Create a 3D Fillet of 0.075:

Create a 3D Fillet of 0.075

### Looks like this? Save As!:

Looks like this? Save As! Now save this to the Pizza Cutter Folder 17D-Cap

### Part 5- Handle Base Draw circle DIA 1.25” & Extrude it 5” (centered):

Part 5- Handle Base Draw circle DIA 1.25” & Extrude it 5” (centered)

### Create New Sketch on the bottom of the “tube”. Draw the circle & rectangle to match.:

Create New Sketch on the bottom of the “tube”. Draw the circle & rectangle to match.

### Extrude it out 3/8”:

Extrude it out 3/8”

### Add a Fillet R=0.30 to the top edge:

Add a Fillet R=0.30 to the top edge

### Create a New Offset Workplane from the YZ Plane at 0”:

Create a New Offset Workplane from the YZ Plane at 0”

### Look at it from the side & add New Sketch to the Work Plane:

Look at it from the side & add New Sketch to the Work Plane

### Now Rt Click & select Slice Graphics or hit the F7 key:

Now Rt Click & select Slice Graphics or hit the F7 key

### You should now see this:

You should now see this

### Draw this to match:

Draw this to match

### Create two Fillets w/R of 0.04”:

Create two Fillets w/R of 0.04”

### Pattern; Rectangular:

Pattern; Rectangular

### Select the sketch:

Select the sketch

### Direction 1 is “bottom” line; Opposite Direction; 8; Distance 0.25”:

Direction 1 is “bottom” line; Opposite Direction; 8; Distance 0.25”

### Model; Revolve; Cut; the 8 Profiles:

Model; Revolve; Cut; the 8 Profiles

Axis = Z Axis

### Should look like this:

Should look like this

### Create a New Offset Workplane from the XZ Plane at 5/8”:

Create a New Offset Workplane from the XZ Plane at 5/8”

### Draw a Circle w/DIA = 0.5”; On Center; 4.5” from the bottom:

Draw a Circle w/DIA = 0.5”; On Center; 4.5” from the bottom

### Create a Hole; Through All; DIA = 0.50”:

Create a Hole; Through All; DIA = 0.50”

### Should look like this: (Rt Click & turn the Workplane Visibility Off):

Should look like this: ( Rt Click & turn the Workplane Visibility Off)

### Add 3D Fillet; R= 0.075”; Both sides:

Add 3D Fillet; R= 0.075”; Both sides

### Should look like this: Now change its material/color to something you like.:

Should look like this: Now change its material/color to something you like.

### Save As! 17E-Handle :

Save As! 17E-Handle

### Part 6- Rivet Draw to match:

Part 6- Rivet Draw to match

### Create a Model; Revolve; so that it looks like this :

Create a Model; Revolve; so that it looks like this

### Create a 3D Fillet 0.02R of the two bottom edges:

Create a 3D Fillet 0.02R of the two bottom edges

### Should look like this:

Should look like this

### Change the material to a color you like & save it as 17F-Rivet:

Change the material to a color you like & save it as 17F-Rivet