Distillation_good

Views:
 
Category: Entertainment
     
 

Presentation Description

No description available.

Comments

Presentation Transcript

PENDAHULUAN :

PENDAHULUAN Distillation didefinisikan sebagai : suatu proses dimana campuran cairan atau uap dari dua zat atau lebih dipisahkan menjadi fraksi komponen-komponennya sesuai dengan kemurnian yang diinginkan, dengan menggunakan atau menghilangkan panas. Distilasi berdasarkan fakta bahwa uap yang dihasilkan dari campuran yang mendidih akan lebih kaya komponen yang titik didihnya lebih tinggi dibanding dengan komponen yang mempunyai titik didih yang lebih rendah. Oleh karena itu, ketika uap tersebut didinginkan dan dikondensasikan, hasil kondensatnya akan mengandung lebih banyak komponen voletile. Pada keadaan yang sama, komponen yang kurang voletile jumlahnya lebih sedikit. Kolom Distilasi didisain untuk mendapatkan pemisahan ini secara efisien.

Introduction:

Introduction Although many people have a fair idea what “distillation” means, the important aspects that seem to be missed from the manufacturing point of view are that: distillation is the most common separation technique it consumes enormous amounts of energy, both in terms of cooling and heating requirements it can contribute to more than 50% of plant operating costs The best way to reduce operating costs of existing units, is to improve their efficiency and operation via process optimisation and control. To achieve this improvement, a thorough understanding of distillation principles and how distillation systems are designed is essential.

Introduction:

Introduction The purpose of this set of notes is to expose you to the terminology used in distillation practice and to give a very basic introduction to: types of columns basic distillation equipment and operation column internals reboilers distillation principles vapour liquid equilibria distillation column design and the factors that affect distillation column operation

TYPES OF DISTILLATION COLUMNS:

TYPES OF DISTILLATION COLUMNS There are many types of distillation columns, each designed to perform specific types of separations, and each design differs in terms of complexity.

TYPES OF DISTILLATION COLUMNS:

TYPES OF DISTILLATION COLUMNS Batch and Continuous Columns One way of classifying distillation column type is to look at how they are operated. Thus we have: batch and continuous columns. Batch Columns In batch operation , the feed to the column is introduced batch-wise. That is, the column is charged with a 'batch' and then the distillation process is carried out. When the desired task is achieved, a next batch of feed is introduced. Continuous Columns In contrast, continuous columns process a continuous feed stream. No interruptions occur unless there is a problem with the column or surrounding process units. They are capable of handling high throughputs and are the most common of the two types. We shall concentrate only on this class of columns.

TYPES OF DISTILLATION COLUMNS:

TYPES OF DISTILLATION COLUMNS Types of Continuous Columns Continuous columns can be further classified according to: the nature of the feed that they are processing , binary column - feed contains only two components multi-component column - feed contains more than two components the number of product streams they have multi-product column - column has more than two product streams where the extra feed exits when it is used to help with the separation , extractive distillation - where the extra feed appears in the bottom product stream azeotropic distillation - where the extra feed appears at the top product stream

TYPES OF DISTILLATION COLUMNS:

TYPES OF DISTILLATION COLUMNS Types of Continuous Columns the type of column internals tray column - where trays of various designs are used to hold up the liquid to provide better contact between vapour and liquid, hence better separation packed column - where instead of trays, 'packings' are used to enhance contact between vapour and liquid

BASIC DISTILLATION EQUIPMENT AND OPERATION:

BASIC DISTILLATION EQUIPMENT AND OPERATION Main Components of Distillation Columns Distillation columns are made up of several components, each of which is used either to tranfer heat energy or enhance materail transfer. A typical distillation contains several major components: a vertical shell where the separation of liquid components is carried out column internals such as trays/plates and/or packings which are used to enhance component separations a reboiler to provide the necessary vaporisation for the distillation process a condenser to cool and condense the vapour leaving the top of the column a reflux drum to hold the condensed vapour from the top of the column so that liquid ( reflux ) can be recycled back to the column

BASIC DISTILLATION EQUIPMENT AND OPERATION:

BASIC DISTILLATION EQUIPMENT AND OPERATION The vertical shell houses the column internals and together with the condenser and reboiler, constitute a distillation column. A schematic of a typical distillation unit with a single feed and two product streams is shown below:

BASIC DISTILLATION EQUIPMENT AND OPERATION:

BASIC DISTILLATION EQUIPMENT AND OPERATION Basic Operation and Terminology The liquid mixture that is to be processed is known as the feed and this is introduced usually somewhere near the middle of the column to a tray known as the feed tray . The feed tray divides the column into a top ( enriching or rectification ) section and a bottom ( stripping ) section. The feed flows down the column where it is collected at the bottom in the reboiler .

BASIC DISTILLATION EQUIPMENT AND OPERATION:

BASIC DISTILLATION EQUIPMENT AND OPERATION Basic Operation and Terminology Heat is supplied to the reboiler to generate vapour. The source of heat input can be any suitable fluid, although in most chemical plants this is normally steam. In refineries, the heating source may be the output streams of other columns.  The vapour raised in the reboiler is re-introduced into the unit at the bottom of the column. The liquid removed from the reboiler is known as the bottoms product or simply, bottoms .

BASIC DISTILLATION EQUIPMENT AND OPERATION:

BASIC DISTILLATION EQUIPMENT AND OPERATION Basic Operation and Terminology The vapour moves up the column, and as it exits the top of the unit, it is cooled by a condenser . The condensed liquid is stored in a holding vessel known as the reflux drum . Some of this liquid is recycled back to the top of the column and this is called the reflux . The condensed liquid that is removed from the system is known as the distillate or top product . Thus, there are internal flows of vapour and liquid within the column as well as external flows of feeds and product streams, into and out of the column.

COLUMN INTERNALS:

COLUMN INTERNALS Trays and Plates The terms "trays" and "plates" are used interchangeably. There are many types of tray designs, but the most common ones are : Bubble cap trays A bubble cap tray has riser or chimney fitted over each hole, and a cap that covers the riser. The cap is mounted so that there is a space between riser and cap to allow the passage of vapour. Vapour rises through the chimney and is directed downward by the cap, finally discharging through slots in the cap, and finally bubbling through the liquid on the tray.

COLUMN INTERNALS:

COLUMN INTERNALS Valve trays In valve trays, perforations are covered by liftable caps. Vapour flows lifts the caps, thus self creating a flow area for the passage of vapour. The lifting cap directs the vapour to flow horizontally into the liquid, thus providing better mixing than is possible in sieve trays.

COLUMN INTERNALS:

COLUMN INTERNALS Sieve trays Sieve trays are simply metal plates with holes in them. Vapour passes straight upward through the liquid on the plate. The arrangement, number and size of the holes are design parameters.   Because of their efficiency, wide operating range, ease of maintenance and cost factors, sieve and valve trays have replaced the once highly thought of bubble cap trays in many applications.

COLUMN INTERNALS:

COLUMN INTERNALS Liquid and Vapour Flows in a Tray Column The next few figures show the direction of vapour and liquid flow across a tray, and across a column.

COLUMN INTERNALS:

COLUMN INTERNALS Each tray has 2 conduits, one on each side, called ‘ downcomers ’. Liquid falls through the downcomers by gravity from one tray to the one below it. The flow across each plate is shown in the above diagram on the right. A weir on the tray ensures that there is always some liquid ( holdup ) on the tray and is designed such that the the holdup is at a suitable height, e.g. such that the bubble caps are covered by liquid. Being lighter, vapour flows up the column and is forced to pass through the liquid, via the openings on each tray. The area allowed for the passage of vapour on each tray is called the active tray area.

COLUMN INTERNALS:

COLUMN INTERNALS The picture  on the left is a photograph of a section of a pilot scale column equiped with bubble capped trays. The tops of the 4 bubble caps on the tray can just be seen. The down- comer in this case is a pipe, and is shown on the right. The frothing of the liquid on the active tray area is due to both passage of vapour from the tray below as well as boiling.

COLUMN INTERNALS:

COLUMN INTERNALS As the hotter vapour passes through the liquid on the tray above, it transfers heat to the liquid. In doing so, some of the vapour condenses adding to the liquid on the tray. The condensate, however, is richer in the less volatile components than is in the vapour. Additionally, because of the heat input from the vapour, the liquid on the tray boils, generating more vapour. This vapour, which moves up to the next tray in the column, is richer in the more volatile components. This continuous contacting between vapour and liquid occurs on each tray in the column and brings about the separation between low boiling point components and those with higher boiling

COLUMN INTERNALS:

COLUMN INTERNALS Tray Designs A tray essentially acts as a mini-column, each accomplishing a fraction of the separation task. From this we can deduce that the more trays there are, the better the degree of separation and that overall separation efficiency will depend significantly on the design of the tray. Trays are designed to maximise vapour-liquid contact by considering the liquid distribution and vapour distribution on the tray. This is because better vapour-liquid contact means better separation at each tray, translating to better column performance. Less trays will be required to achieve the same degree of separation. Attendant benefits include less energy usage and lower construction costs. There is a clear trend to improve separations by supplementing the use of trays by additions of packings.

COLUMN INTERNALS:

COLUMN INTERNALS Packings Packings are passive devices that are designed to increase the interfacial area for vapour-liquid contact. The following pictures show 3 different types of packings. These strangely shaped pieces are supposed to impart good vapour-liquid contact when a particular type is placed together in numbers, without causing excessive pressure-drop across a packed section. This is important because a high pressure drop would mean that more energy is required to drive the vapour up the distillation column.

COLUMN INTERNALS:

COLUMN INTERNALS Packings versus Trays A tray column that is facing throughput problems may be de-bottlenecked by replacing a section of trays with packings. This is because: packings provide extra inter-facial area for liquid-vapour contact efficiency of separation is increased for the same column height packed columns are shorter than trayed columns Packed columns are called continuous-contact columns while trayed columns are called staged-contact columns because of the manner in which vapour and liquid are contacted.

COLUMN REBOILERS :

COLUMN REBOILERS There are a number of designs of reboilers. It is beyond the scope of this set of introductory notes to delve into their design principles. However, they can be regarded as heat-exchangers that are required to transfer enough energy to bring the liquid at the bottom of the column to boiling boint. The following are examples of typical reboiler types.

COLUMN REBOILERS:

COLUMN REBOILERS

COLUMN REBOILERS:

COLUMN REBOILERS

DISTILLATION PRINCIPLES:

DISTILLATION PRINCIPLES Separation of components from a liquid mixture via distillation depends on the differences in boiling points of the individual components. Also, depending on the concentrations of the components present, the liquid mixture will have different boiling point characteristics. Therefore, distillation processes depends on the vapour pressure characteristics of liquid mixtures.

DISTILLATION PRINCIPLES:

DISTILLATION PRINCIPLES Vapour Pressure and Boiling The vapour pressure of a liquid at a particular temperature is the equilibrium pressure exerted by molecules leaving and entering the liquid surface. Here are some important points regarding vapour pressure: energy input raises vapour pressure vapour pressure is related to boiling a liquid is said to ‘boil’ when its vapour pressure equals the surrounding pressure the ease with which a liquid boils depends on its volatility liquids with high vapour pressures (volatile liquids) will boil at lower temperatures the vapour pressure and hence the boiling point of a liquid mixture depends on the relative amounts of the components in the mixture distillation occurs because of the differences in the volatility of the components in the liquid mixture

DISTILLATION PRINCIPLES:

DISTILLATION PRINCIPLES The Boiling Point Diagram The boiling point diagram shows how the equilibrium compositions of the components in a liquid mixture vary with temperature at a fixed pressure. Consider an example of a liquid mixture containing 2 components (A and B) - a binary mixture. This has the following boiling point diagram. The boiling point of A is that at which the mole fraction of A is 1. The boiling point of B is that at which the mole fraction of A is 0. In this example, A is the more volatile component and therefore has a lower boiling point than B. The upper curve in the diagram is called the dew-point curve while the lower one is called the bubble-point curve .

DISTILLATION PRINCIPLES:

DISTILLATION PRINCIPLES The dew-point is the temperature at which the saturated vapour starts to condense . The bubble-point is the temperature at which the liquid starts to boil . The region above the dew-point curve shows the equilibrium composition of the superheated vapour while the region below the bubble-point curve shows the equilibrium composition of the subcooled liquid.

DISTILLATION PRINCIPLES:

DISTILLATION PRINCIPLES For example, when a subcooled liquid with mole fraction of A=0.4 (point A) is heated, its concentration remains constant until it reaches the bubble-point (point B), when it starts to boil. The vapours evolved during the boiling has the equilibrium composition given by point C, approximately 0.8 mole fraction A. This is approximately 50% richer in A than the original liquid. This difference between liquid and vapour compositions is the basis for distillation operations.

DISTILLATION PRINCIPLES:

DISTILLATION PRINCIPLES Relative Volatility Relative volatility is a measure of the differences in volatility between 2 components, and hence their boiling points. It indicates how easy or difficult a particular separation will be. The relative volatility of component ‘i’ with respect to component ‘j’ is defined as y i = mole fraction of component ‘i’ in the vapour x i = mole fraction of component ‘i’ in the liquid Thus if the relative volatility between 2 components is very close to one, it is an indication that they have very similar vapour pressure characteristics. This means that they have very similar boiling points and therefore, it will be difficult to separate the two components via distillation.

VAPOUR LIQUID EQUILIBRIA:

VAPOUR LIQUID EQUILIBRIA Distillation columns are designed based on the boiling point properties of the components in the mixtures being separated. Thus the sizes, particularly the height, of distillation columns are determined by the vapour liquid equilibrium (VLE) data for the mixtures.

VAPOUR LIQUID EQUILIBRIA:

VAPOUR LIQUID EQUILIBRIA Vapour-Liquid-Equilibrium (VLE) Curves Constant pressure VLE data is obtained from boiling point diagrams . VLE data of binary mixtures is often presented as a plot, as shown in the figure on the right. The VLE plot expresses the bubble-point and the dew-point of a binary mixture at constant pressure. The curved line is called the equilibrium line and describes the compositions of the liquid and vapour in equilibrium at some fixed pressure.

VAPOUR LIQUID EQUILIBRIA:

VAPOUR LIQUID EQUILIBRIA This particular VLE plot shows a binary mixture that has a uniform vapour-liquid equilibrium that is relatively easy to separate. The next two VLE plots below on the other hand, shows non-ideal systems which will present more difficult separations. We can tell from the shapes of the curves and this will be explained further later on.

VAPOUR LIQUID EQUILIBRIA:

VAPOUR LIQUID EQUILIBRIA The most intriguing VLE curves are generated by azeotropic systems. An azeotrope is a liquid mixture which when vaporised, produces the same composition as the liquid . The two VLE plots below, show two different azeotropic systems, one with a minimum boiling point and one with a maximum boiling point. In both plots, the equilibrium curves cross the diagonal lines, and this are azeotropic points where the azeotropes occur. In other words azeotropic systems give rise to VLE plots where the equilibrium curves crosses the diagonals.

VAPOUR LIQUID EQUILIBRIA:

VAPOUR LIQUID EQUILIBRIA Note the shapes of the respective equilibrium lines in relation to the diagonal lines that bisect the VLE plots.

VAPOUR LIQUID EQUILIBRIA:

VAPOUR LIQUID EQUILIBRIA Both plots are however, obtained from homogenous azeotropic systems. An azeotrope that contains one liquid phase in contact with vapour is called a homogenous azeotrope . A homogenous azeotrope cannot be separated by conventional distillation . However, vacumn distillation may be used as the lower pressures can shift the azeotropic point.Alternatively, an additional substance may added to shift the azeotropic point to a more ‘favourable’ position. When this additional component appears in appreciable amounts at the top of the column, the operation is called azeotropic distillation . When the additional component appears mostly at the bottom of the column, the operation is called extractive distillation

VAPOUR LIQUID EQUILIBRIA:

VAPOUR LIQUID EQUILIBRIA The most intriguing VLE curves are generated by azeotropic systems. An azeotrope is a liquid mixture which when vaporised, produces the same composition as the liquid . The two VLE plots below, show two different azeotropic systems, one with a minimum boiling point and one with a maximum boiling point. In both plots, the equilibrium curves cross the diagonal lines, and this are azeotropic points where the azeotropes occur. In other words azeotropic systems give rise to VLE plots where the equilibrium curves crosses the diagonals.

VAPOUR LIQUID EQUILIBRIA:

VAPOUR LIQUID EQUILIBRIA Note the shapes of the respective equilibrium lines in relation to the diagonal lines that bisect the VLE plots.

VAPOUR LIQUID EQUILIBRIA:

VAPOUR LIQUID EQUILIBRIA The VLE curve on the left is also generated by an azeotropic system, in this case a heterogenous azeotrope . Heterogenous azeotropes can be identified by the ‘flat’ portion on the equilibrium diagram. They may be separated in 2 distillation columns since these substances usually form two liquid phases with widely differing compositions. The phases may be separated using settling tanks under appropriate conditions.

DISTILLATION COLUMN DESIGN:

DISTILLATION COLUMN DESIGN As mentioned, distillation columns are designed using VLE data for the mixtures to be separated. The vapour-liquid equilibrium characteristics (indicated by the shape of the equilibrium curve) of the mixture will determine the number of stages, and hence the number of trays, required for the separation. This is illustrated clearly by applying the McCabe-Thiele method to design a binary column.

DISTILLATION COLUMN DESIGN:

DISTILLATION COLUMN DESIGN McCABE-THIELE DESIGN METHOD The McCabe-Thiele approach is a graphical one, and uses the VLE plot to determine the theoretical number of stages required to effect the separation of a binary mixture. It assumes constant molar overflow and this implies that: molal heats of vaporization of the components are roughly the same heat effects (heats of solution, heat losses to and from column, etc.) are negligible for every mole of vapor condensed, 1 mole of liquid is vaporized

DISTILLATION COLUMN DESIGN:

DISTILLATION COLUMN DESIGN The design procedure is simple. Given the VLE diagram of the binary mixture, operating lines are drawn first. Operating lines define the mass balance relationships between the liquid and vapour phases in the column. There is one operating line for the bottom (stripping) section of the column, and on for the top (rectification or enriching) section of the column. Use of the constant molar overflow assumption also ensures the the operating lines are straight lines.

DISTILLATION COLUMN DESIGN:

DISTILLATION COLUMN DESIGN Operating Line for the Rectification Section   The operating line for the rectification section is constructed as follows. First the desired top product composition is located on the VLE diagram, and a vertical line produced until it intersects the diagonal line that splits the VLE plot in half. A line with slope R/(R+1) is then drawn from this instersection point as shown in the diagram below.   R is the ratio of reflux flow ( L ) to distillate flow ( D ) and is called the reflux ratio and is a measure of how much of the material going up the top of the column is returned back to the column as reflux.

DISTILLATION COLUMN DESIGN:

DISTILLATION COLUMN DESIGN Operating Line for the Stripping Section   The operating line for the stripping section is constructed in a similar manner. However, the starting point is the desired bottom product composition. A vertical line is drawn from this point to the diagonal line, and a line of slope L s /V s is drawn as illustrated in the diagram below. L s is the liquid rate down the stripping section of the column, while V s is the vapour rate up the stripping section of the column. Thus the slope of the operating line for the stripping section is a ratio between the liquid and vapour flows in that part of the column.

DISTILLATION COLUMN DESIGN:

DISTILLATION COLUMN DESIGN

DISTILLATION COLUMN DESIGN:

DISTILLATION COLUMN DESIGN Equilibrium and Operating Lines   The McCabe-Thiele method assumes that the liquid on a tray and the vapour above it are in equilibrium. How this is related to the VLE plot and the operating lines is depicted graphically in the diagram on the right.

DISTILLATION COLUMN DESIGN:

DISTILLATION COLUMN DESIGN

DISTILLATION COLUMN DESIGN:

DISTILLATION COLUMN DESIGN A magnified section of the operating line for the stripping section is shown in relation to the corresponding n'th  stage in the column. L's are the liquid flows while V's are the vapour flows. x and y denote liquid and vapour compositions and the subscripts denote the origin of the flows or compositions. That is ' n-1 ' will mean from the stage below stage 'n ' while 'n+1' will mean from the stage above stage 'n' . The liquid in stage 'n' and the vapour above it are in equilibrium, therefore, x n and y n lie on the equilibrium line. Since the vapour is carried to the tray above without changing composition, this is depicted as a horizontal line on the VLE plot. Its intersection with the  operating line will give the composition of the liquid on tray 'n+1' as the operating line defines the material balance on the trays. The composition of the vapour above the 'n+1' tray is obtained from the intersection of the vertical line from this point to the equilibrium line.

DISTILLATION COLUMN DESIGN:

DISTILLATION COLUMN DESIGN Number of Stages and Trays   Doing the graphical construction repeatedly will give rise to a number of 'corner' sections, and each section will be equivalent to a stage of the distillation. This is the basis of sizing distillation columns using the McCabe-Thiele graphical design methodology as shown in the following example.

DISTILLATION COLUMN DESIGN:

DISTILLATION COLUMN DESIGN Given the operating lines for both stripping and rectification sections, the graphical construction described above was applied. This particular example shows that 7 theoretical stages are required to achieve the desired separation. The required number of trays (as opposed to stages)  is one less than the number of stages since the graphical construction includes the contribution of the reboiler in carrying out the separation.

DISTILLATION COLUMN DESIGN:

DISTILLATION COLUMN DESIGN The actual number of trays required is given by the formula: (number of theoretical trays)/(tray efficiency) Typical values for tray efficiency ranges from 0.5 to 0.7 and depends on a number of factors, such as the type of trays being used, and internal liquid and vapour flow conditions. Sometimes, additional trays are added (up to 10%) to accomodate the possibility that the column may be under-designed.

DISTILLATION COLUMN DESIGN:

DISTILLATION COLUMN DESIGN As mentioned, distillation columns are designed using VLE data for the mixtures to be separated. The vapour-liquid equilibrium characteristics (indicated by the shape of the equilibrium curve) of the mixture will determine the number of stages, and hence the number of trays, required for the separation. This is illustrated clearly by applying the McCabe-Thiele method to design a binary column.

DISTILLATION COLUMN DESIGN:

DISTILLATION COLUMN DESIGN McCABE-THIELE DESIGN METHOD The McCabe-Thiele approach is a graphical one, and uses the VLE plot to determine the theoretical number of stages required to effect the separation of a binary mixture. It assumes constant molar overflow and this implies that: molal heats of vaporisation of the components are roughly the same heat effects (heats of solution, heat losses to and from column, etc.) are negligible for every mole of vapour condensed, 1 mole of liquid is vaporised

DISTILLATION COLUMN DESIGN:

DISTILLATION COLUMN DESIGN The design procedure is simple. Given the VLE diagram of the binary mixture, operating lines are drawn first. Operating lines define the mass balance relationships between the liquid and vapour phases in the column. There is one operating line for the bottom (stripping) section of the column, and on for the top (rectification or enriching) section of the column. Use of the constant molar overflow assumption also ensures the the operating lines are straight lines.

DISTILLATION COLUMN DESIGN:

DISTILLATION COLUMN DESIGN Operating Line for the Rectification Section   The operating line for the rectification section is constructed as follows. First the desired top product composition is located on the VLE diagram, and a vertical line produced until it intersects the diagonal line that splits the VLE plot in half. A line with slope R/(R+1) is then drawn from this instersection point as shown in the diagram below.   R is the ratio of reflux flow ( L ) to distillate flow ( D ) and is called the reflux ratio and is a measure of how much of the material going up the top of the column is returned back to the column as reflux.

DISTILLATION COLUMN DESIGN:

DISTILLATION COLUMN DESIGN Operating Line for the Stripping Section   The operating line for the stripping section is constructed in a similar manner. However, the starting point is the desired bottom product composition. A vertical line is drawn from this point to the diagonal line, and a line of slope L s /V s is drawn as illustrated in the diagram below. L s is the liquid rate down the stripping section of the column, while V s is the vapour rate up the stripping section of the column. Thus the slope of the operating line for the stripping section is a ratio between the liquid and vapour flows in that part of the column.

DISTILLATION COLUMN DESIGN:

DISTILLATION COLUMN DESIGN

DISTILLATION COLUMN DESIGN:

DISTILLATION COLUMN DESIGN Equilibrium and Operating Lines   The McCabe-Thiele method assumes that the liquid on a tray and the vapour above it are in equilibrium. How this is related to the VLE plot and the operating lines is depicted graphically in the diagram on the right.

DISTILLATION COLUMN DESIGN:

DISTILLATION COLUMN DESIGN

DISTILLATION COLUMN DESIGN:

DISTILLATION COLUMN DESIGN A magnified section of the operating line for the stripping section is shown in relation to the corresponding n'th  stage in the column. L's are the liquid flows while V's are the vapour flows. x and y denote liquid and vapour compositions and the subscripts denote the origin of the flows or compositions. That is ' n-1 ' will mean from the stage below stage 'n ' while 'n+1' will mean from the stage above stage 'n' . The liquid in stage 'n' and the vapour above it are in equilibrium, therefore, x n and y n lie on the equilibrium line. Since the vapour is carried to the tray above without changing composition, this is depicted as a horizontal line on the VLE plot. Its intersection with the  operating line will give the composition of the liquid on tray 'n+1' as the operating line defines the material balance on the trays. The composition of the vapour above the 'n+1' tray is obtained from the intersection of the vertical line from this point to the equilibrium line.

DISTILLATION COLUMN DESIGN:

DISTILLATION COLUMN DESIGN Number of Stages and Trays   Doing the graphical construction repeatedly will give rise to a number of 'corner' sections, and each section will be equivalent to a stage of the distillation. This is the basis of sizing distillation columns using the McCabe-Thiele graphical design methodology as shown in the following example.

DISTILLATION COLUMN DESIGN:

DISTILLATION COLUMN DESIGN Given the operating lines for both stripping and rectification sections, the graphical construction described above was applied. This particular example shows that 7 theoretical stages are required to achieve the desired separation. The required number of trays (as opposed to stages)  is one less than the number of stages since the graphical construction includes the contribution of the reboiler in carrying out the separation.

DISTILLATION COLUMN DESIGN:

DISTILLATION COLUMN DESIGN The Feed Line (q-line)   The diagram above also shows that the binary feed should be introduced at the 4'th stage. However, if the feed composition is such that it does not coincide with the intersection of the operating lines, this means that the feed is not a saturated liquid. The condition of the feed can be deduced by the slope of the feed line or q-line . The q-line is that drawn between the intersection of the operating lines, and where the feed composition lies on the diagonal line

DISTILLATION COLUMN DESIGN:

DISTILLATION COLUMN DESIGN Depending on the state of the feed, the feed lines will have different slopes. For example, q = 0 (saturated vapour) q = 1 (saturated liquid) 0 < q < 1 (mix of liquid and vapour) q > 1 (subcooled liquid) q < 0 (superheated vapour) The q-lines for the various feed conditions are shown in the diagram on the left.

DISTILLATION COLUMN DESIGN:

DISTILLATION COLUMN DESIGN Using Operating Lines and the Feed Line in McCabe-Thiele Design   If we have information about the condition of the feed mixture, then we can construct the q-line and use it in the McCabe-Thiele design. However, excluding the equilibrium line, only two other pairs of lines can be used in the McCabe-Thiele procedure. These are: feed-line and rectification section operating line feed-line and stripping section operating line stripping and rectification operating lines This is because these pairs of lines determine the third.

DISTILLATION COLUMN DESIGN:

DISTILLATION COLUMN DESIGN OVERALL COLUMN DESIGN Determining the number of stages required for the desired degree of separation and the location of the feed tray is merely the first steps in producing an overall distillation column design. Other things that need to be considered are tray spacings; column diameter; internal configurations; heating and cooling duties . All of these can lead to conflicting design parameters. Thus, distillation column design is often an iterative procedure. If the conflicts are not resolved at the design stage, then the column will not perform well in practice. The next set of notes will discuss the factors that can affect distillation column performance.

EFFECTS OF THE NUMBER OF TRAYS OR STAGES:

EFFECTS OF THE NUMBER OF TRAYS OR STAGES Here we will expand on the design of columns by looking briefly at the effects of the number of trays, and the position of the feed tray, and on the performances of distillation columns

EFFECTS OF THE NUMBER OF TRAYS OR STAGES:

EFFECTS OF THE NUMBER OF TRAYS OR STAGES Effects of the Number of Trays   It can be deduced from the previous section on distillation column design that the number of trays will influence the degree of separation. This is illustrated by the following example. Consider as a base case, a 10 stage column. The feed is a binary mixture that has a composition of 0.5 mole fraction in terms of the more volatile component, and introduced at stage 5. The steady-state terminal compositions of about 0.65 at the top (stage 1) and 0.1 at the bottom (stage 10) are shown below:

EFFECTS OF THE NUMBER OF TRAYS OR STAGES:

EFFECTS OF THE NUMBER OF TRAYS OR STAGES Composition Profile: 10 stages, feed at stage 5

EFFECTS OF THE NUMBER OF TRAYS OR STAGES:

EFFECTS OF THE NUMBER OF TRAYS OR STAGES Suppose we decrease the number of stages to 8, and keep the feed at the middle stage, i.e. stage 4. The resulting composition profile is: Composition Profile: 8 stages, feed at stage 4 We can see that the top composition has decreased while the bottom composition has increased. That is, the separation is poorer.

EFFECTS OF THE NUMBER OF TRAYS OR STAGES:

EFFECTS OF THE NUMBER OF TRAYS OR STAGES Now, if we increase the number of stages to 12, and again introduce the feed at mid-column, i.e. stage 6, the composition profile we get is: Composition Profile: 12 stages, feed at stage 6

EFFECTS OF THE NUMBER OF TRAYS OR STAGES:

EFFECTS OF THE NUMBER OF TRAYS OR STAGES Again, the composition has changed. This time the distillate is much richer in the more volatile component, while the bottoms has less, indicating better separation. Thus, increasing the number of stages will improve separation .

EFFECTS OF THE NUMBER OF TRAYS OR STAGES:

EFFECTS OF THE NUMBER OF TRAYS OR STAGES Effect of Feed Tray Position   Here we look at how the position of the feed tray affects separation efficiency. Suppose we have a 20 stage column, again separating a binary mixture that has a composition of 0.5 mole fraction in terms of the more volatile component. The terminal compositions obtained when the feed is introduced at stages 5, 10 and 15 (at fixed reflux and re-boil rates) are shown in the following plots.

EFFECTS OF THE NUMBER OF TRAYS OR STAGES:

EFFECTS OF THE NUMBER OF TRAYS OR STAGES Composition profile: 20 stages, feed at stage 5

EFFECTS OF THE NUMBER OF TRAYS OR STAGES:

EFFECTS OF THE NUMBER OF TRAYS OR STAGES Composition profile: 20 stages, feed at stage 10

EFFECTS OF THE NUMBER OF TRAYS OR STAGES:

EFFECTS OF THE NUMBER OF TRAYS OR STAGES Composition profile: 20 stages, feed at stage 15

EFFECTS OF THE NUMBER OF TRAYS OR STAGES:

EFFECTS OF THE NUMBER OF TRAYS OR STAGES As the feed stage is moved lower down the column, the top composition becomes less rich in the more volatile component while the bottoms contains more of the more volatile component. However, the changes in top composition is not as marked as the bottoms composition. The preceding examples illustrate what can happen if the position of the feed tray is shifted for this particular system. They should not be used to generalise to other distillation systems, as the effects are not straightforward.

PowerPoint Presentation:

FACTORS AFFECTING DISTILLATION COLUMN OPERATION The performance of a distillation column is determined by many factors, for example: feed conditions : state of feed composition of feed trace elements that can severely affect the VLE of liquid mixtures internal liquid and fluid flow conditions state of trays (packings) weather conditions

FACTORS AFFECTING DISTILLATION COLUMN OPERATION:

FACTORS AFFECTING DISTILLATION COLUMN OPERATION Feed Conditions   The state of the feed mixture and feed composition affects the operating lines and hence the number of stages required for separation. It also affects the location of feed tray. During operation, if the deviations from design specifications are excessive, then the column may no longer be able handle the separation task. To overcome the problems associated with the feed, some column are designed to have multiple feed points when the feed is expected to containing varying amounts of components.

FACTORS AFFECTING DISTILLATION COLUMN OPERATION:

FACTORS AFFECTING DISTILLATION COLUMN OPERATION Reflux Conditions As the reflux ratio is increased, the gradient of operating line for the rectification section moves towards a maximum value of 1. Physically, what this means is that more and more liquid that is rich in the more volatile components are being recycled back into the column. Separation then becomes better and thus less trays are needed to achieve the same degree of separation . Minimum trays are required under total reflux conditions, i.e. there is no withdrawal of distillate.

FACTORS AFFECTING DISTILLATION COLUMN OPERATION:

FACTORS AFFECTING DISTILLATION COLUMN OPERATION Reflux Conditions On the other hand, as reflux is decreased, the operating line for the rectification section moves towards the equilibrium line. The ‘ pinch ’ between operating and equilibrium lines becomes more pronounced and more and more trays are required.This is easy to verify using the McCabe-Thiele method . The limiting condition occurs at minimum reflux ratio , when an infinite number of trays will be required to effect separation. Most columns are designed to operate between 1.2 to 1.5 times the minimum reflux ratio because this is approximately the region of minimum operating costs (more reflux means higher reboiler duty).

FACTORS AFFECTING DISTILLATION COLUMN OPERATION:

FACTORS AFFECTING DISTILLATION COLUMN OPERATION Vapour Flow Conditions Adverse vapour flow conditions can cause Foaming Entrainment Weeping/dumping Flooding

FACTORS AFFECTING DISTILLATION COLUMN OPERATION:

FACTORS AFFECTING DISTILLATION COLUMN OPERATION Foaming Foaming refers to the expansion of liquid due to passage of vapour or gas. Although it provides high interfacial liquid-vapour contact, excessive foaming often leads to liquid buildup on trays . In some cases, foaming may be so bad that the foam mixes with liquid on the tray above. Whether foaming will occur depends primarily on physical properties of the liquid mixtures, but is sometimes due to tray designs and condition. Whatever the cause, separation efficiency is always reduced.

FACTORS AFFECTING DISTILLATION COLUMN OPERATION:

FACTORS AFFECTING DISTILLATION COLUMN OPERATION Entrainment Entrainment refers to the liquid carried by vapour up to the tray above and is again caused by high vapour flow rates . It is detrimental because tray efficiency is reduced: lower volatile material is carried to a plate holding liquid of higher volatility. It could also contaminate high purity distillate. Excessive entrainment can lead to flooding.

FACTORS AFFECTING DISTILLATION COLUMN OPERATION:

FACTORS AFFECTING DISTILLATION COLUMN OPERATION Weeping/Dumping This phenomenon is caused by low vapour flow. The pressure exerted by the vapour is insufficient to hold up the liquid on the tray. Therefore, liquid starts to leak through perforations . Excessive weeping will lead to dumping. That is the liquid on all trays will crash (dump) through to the base of the column (via a domino effect) and the column will have to be re-started . Weeping is indicated by a sharp pressure drop in the column and reduced separation efficiency.

FACTORS AFFECTING DISTILLATION COLUMN OPERATION:

FACTORS AFFECTING DISTILLATION COLUMN OPERATION Flooding Flooding is brought about by excessive vapour flow, causing liquid to be entrained in the vapour up the column . The increased pressure from excessive vapour also backs up the liquid in the downcomer, causing an increase in liquid holdup on the plate above.  Depending on the degree of flooding, the maximum capacity of the column may be severely reduced. Flooding is detected by sharp increases in column differential pressure and significant decrease in separation efficiency.

FACTORS AFFECTING DISTILLATION COLUMN OPERATION:

FACTORS AFFECTING DISTILLATION COLUMN OPERATION Column Diameter   Most of the above factors that affect column operation is due to vapour flow conditions: either excessive or too low. Vapour flow velocity is dependent on column diameter . Weeping determines the minimum vapour flow required while flooding determines the maximum vapour flow allowed, hence column capacity. Thus, if the column diameter is not sized properly, the column will not perform well. Not only will operational problems occur, the desired separation duties may not be achieved.

FACTORS AFFECTING DISTILLATION COLUMN OPERATION:

FACTORS AFFECTING DISTILLATION COLUMN OPERATION State of Trays and Packings   Remember that the actual number of trays required for a particular separation duty is determined by the efficiency of the plate, and the packings if packings are used. Thus, any factors that cause a decrease in tray efficiency will also change the performance of the column. Tray efficiencies are affected by fouling, wear and tear and corrosion, and the rates at which these occur depends on the properties of the liquids being processed . Thus appropriate materials should be specified for tray construction.

FACTORS AFFECTING DISTILLATION COLUMN OPERATION:

FACTORS AFFECTING DISTILLATION COLUMN OPERATION Weather Conditions   Most distillation columns are open to the atmosphere. Although many of the columns are insulated, changing weather conditions can still affect column operation. Thus the reboiler must be appropriately sized to ensure that enough vapour can be generated during cold and windy spells and that it can be turned down sufficiently during hot seasons. The same applies to condensors.

authorStream Live Help