MSDS Powertec

Views:
 
Category: Entertainment
     
 

Presentation Description

No description available.

Comments

Presentation Transcript

slide 1:

MATERIAL SAFETY DATA SHEET 1 SECTION 1 - PRODUCT IDENTIFICATION Product Trade Name Powertec CAS Number Not Applicable for Mixtures Product Information Motorcyle Engine Oil Product Use For product use guide refer to TDS Company Name Pertua Marketing Corporation Address 70 Old Samson Road Balintawak Quezon City Philippines Telephone Number 632 362 1545 MSDS No POI-MSDS-005 SECTION 2 - HAZARD IDENTIFICATION Principal Hazards R36/37/38 - Irritating to eyes respiratory system and skin Routes of Entry Inhalation Ingestion Eye contact Dermal contact Eye Contact May cause eye irritation from mild to severe. Skin Contact May cause skin irritation. Inhalation If inhaled especially for severe dosage may cause respiratory tract irritation. Ingestion May cause gastrointestinal irritation. SECTION 3 - COMPOSITION INFORMATION Base Oil 80 Additive SECTION 4 - FIRST AID MEASURES Ingestion Rinse mouth out with water. DO NOT induce vomiting. If irritation develops or persists or vomiting has occurred after ingestion seek medical assistance. Eye Rinse cautiously with running water for several minutes. If irritation persists seek medical attention. Skin Contact If skin or hair contact has occurred remove any contaminated clothing and footwear wash skin or hair thoroughly with soap and water. If irritation develops or persists consult a doctor. Inhalation Affected patient must be removed from further exposure into fresh air. Avoid exposing yourself when providing assistance and only enter contaminated environment with adequate respiratory equipment. Lay patient down in a well-ventilated area and reassure them. If not breathing provide artificial respiration and seek immediate medical assistance.

slide 2:

MATERIAL SAFETY DATA SHEET 2 Additional Information Note to Physician: Treat symptomatically. Monitor patient for adverse effect. Protection for First Aiders Do not place oneself in a potentially hazardous situation. Use proper protective personal equipment depending on application. First Aid Facilities Eye wash fountain and safety showers are recommended in the area where the product is being used. SECTION 5 - FIRE FIGHTING MEASURES Fire This product is not flammable under conditions of use. Keep storage tanks pipelines fire exposed surfaces etc. cool with water spray. Flash Point 270ºC Suitable Extinguishing Media CO2 Dry Chemical Foam Unsuitable Extinguishing Media Avoid using full water jet directed at residual material that may be burning. Water may cause splattering on hot oil. Product will float on water. Firefighting Procedures Recommended wearing self-contained breathing apparatus. SECTION 6 - ACCIDENTAL RELEASE MEASURES PERSONAL PROTECTION For small spills wear Nitrile gloves glasses/goggles boots and full-length clothing. During routine operation a respirator is not required. However if mists or vapors are generated an approved organic vapor/particulate respirator is required. For large spills or in confined spaces a full chemically resistant bodysuit is recommended and the atmosphere must be evaluated for oxygen deficiency. If in doubt wear self-contained breathing apparatus. CONTROL MEASURES Ventilate area and extinguish and/or remove all sources of ignition. Stop the leak if safe to do so. Caution: The spilled product will be slippery. Avoid contact with the spilled material. Prevent entry into sewers waterways and basements. EMERGENCY PROCEDURE In the event of a spill or accidental release notify the relevant authorities in accordance with all applicable regulations. CONTAINMENT Contain the spill and absorb with a proprietary absorbent material sand or earth. For large spills prepare a bund/barrier/dyke ahead of the spill to confine the spill and allow later recovery. If there is the possibility of spills to enter drains surface water sewers or watercourses ensure bonding or that drains are covered to minimize the potential for this to occur. CLEANING PROCEDURES: Having contained the spill as mentioned above collect all material quickly and place used absorbent in suitable containers. Follow local regulations for the disposal of waste.

slide 3:

MATERIAL SAFETY DATA SHEET 3 SECTION 7 - HANDLING AND STORAGE Handling Procedures Keep containers closed when not in used. Do not discharge into drains or the environment. Dispose to an authorized waste collection point. Use appropriate containment to avoid environmental contamination. Avoid use in confined areas without adequate ventilation. Wash thoroughly after handling. Launder contaminated clothes before reuse. Empty containers contains product residue which may exhibit hazards of product. Dispose of packaging or containers in accordance with local regional and national regulations. SAFE STORAGE This product is a hydrocarbon-based liquid that will burn if preheated. Store in a well-ventilated area away from direct sunlight ignition sources oxidizing agents foodstuffs and clothing. Keep containers closed when not in use. Containers that have been opened must be carefully resealed and kept upright to prevent leakage. INCOMPATIBILITIES Oxidizing substances including strong acids. SECTION 8 - EXPOSURE CONTROLS PERSONAL PROTECTION Engineering Controls Vapors are heavier than air and will tend to accumulate in low areas. Avoid use in confined space without adequate ventilation. Skin and Hand Protection Wear gloves should there will be a chance of contact with the material. Nitrile rubber gloves are recommended. During normal operating procedures long sleeved clothing is recommended to avoid skin contact. Soiled clothing should be washed with detergent prior to reuse. Eye and Face Protection Wear safety glasses/goggles to avoid eye contact when handling. If there is a risk of splashing during use a full face shield is recommended Respiratory Protection Use respirator with the combination of organic vapor and high efficiency filter cartridge if recommended exposure limit is exceeded. Use self-contained breathing apparatus for entry into confined space for poorly ventilated areas and for large spill clean-up sites. Thermal Protection Not Applicable SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES Physical State Liquid Appearance / Color Light Brown Flash Point 270ºC Explosion Data Material does not have explosive properties Vapor Pressure Not Available pH Not Available

slide 4:

MATERIAL SAFETY DATA SHEET 4 Density at 15ºC 0.872 g/ml Water Solubility Insoluble Percent Solid Not Available Percent Volatile Not Available Vapor Density Not Available Odor Mild Hydrocarbon - characteristic lubricating oil odor Viscosity at 40ºC 144.2 cSt Viscosity at 100ºC 16.17 cSt Boiling Point Not Available Pour Point Temperature -18ºC Melting / Freezing Point Not Available SECTION 10 - STABILITY AND REACTIVITY Stability Material is normally stable at moderately elevated temperatures and pressures. Incompatibility Oxidizing Agents such as peroxides chlorates nitrates and concentrated acids. Hazardous Reaction Keep away from strong oxidizing agents such as strong acids chlorates nitrates and peroxides. Hazardous polymerization does not occur. Conditions to Avoid Observe the usual precautionary measures for handling chemicals. Do not heat the container or leave the container open when not in use. Avoid sources of ignition. SECTION 11 - TOXICOLOGICAL INFORMATION Oral Toxicity May lead to pulmonary edema or chemical pneumonitis. Eye Irritation May cause eye irritation. Skin Irritation A skin irritant. Prolonged or repeated skin contact may include redness edema drying and cracking of the skin. Dermal Toxicity Not Available Inhalation Toxicity Not Available Respiratory Irritation If materials is misted or if vapors are generated from heating exposure may cause irritation of mucous membranes and the upper respiratory tract. SECTION 12 - ECOLOGICAL INFORMATION Ecotoxity No data available from manufacturer SECTION 13 - DISPOSAL CONSIDERATIONS

slide 5:

MATERIAL SAFETY DATA SHEET 5 DISPOSAL METHODS PRODUCT The product should not be released to the environment so any unused material should be recycled wherever possible or be disposed of as hazardous waste at an appropriate collection point. Spilled product that cannot be recovered should be absorbed and then shovel into a suitable waste container such as a plastic drum and then be treated as a solid waste. Follow government regulations for disposal of such waste. DISPOSAL METHODS CONTAINER Empty containers may contain residual oil. They should be completely drained and then stored until reconditioned or disposed of. SECTION 14 - TRANSPORT INFORMATION Not classified as hazardous material for transport SECTION 15 - REGULATORY INFORMATION Danger Label None Safety Phrases None SECTION 16 - ANY OTHER RELEVANT INFORMATION Preparation Date 08/04/15 Prepared By POI QC Department Revision Number 1 Material Safety Data Sheet contains health and safety information. For usage guide refer to product TDS. Some Physical and Chemical values are typical values and does not contribute for a specification.

authorStream Live Help