FUSION

FUSION Switching and Electronic Displays Overview: 

FUSION Switching and Electronic Displays Overview

The FUSION Electronic Displays Group: 

The FUSION Electronic Displays Group Key Competencies Project Scoping and Concept Design Custom Fixture and Electronic Component Design and Manufacture Project Management Start to Finish Installation and Testing After Sales Support via USA Office Tech Support Call Centre

Complete Retail Solutions: 

Complete Retail Solutions From Concept to Design Through to Manufacture, Installation and Support, FUSION Electronic Displays offer a Complete Turn-Key Solution for Retail Merchandising

FUSION Project Methods: 

FUSION Project Methods

FUSION Concept Design: 

FUSION Concept Design Initial meetings with clients are used to create concept drawings

FUSION Concept Design: 

FUSION Concept Design 3D models are created from concept drawings and presented to clients

FUSION Concept Design: 

FUSION Concept Design FUSION manufacturing partners create prototype fixtures based on 3D models Prototype fixtures are used to create and test wiring looms for the fixture

FUSION Concept Design: 

FUSION Concept Design Once prototypes are approved, initial production of fixtures begins

FUSION Concept Design: 

FUSION Concept Design Wire looms are created concurrently and shipped in time for integration into the fixture at the factory

FUSION Concept Design: 

FUSION Concept Design All FUSION fixtures are completely assembled, wired and tested at the factory prior to shipment

FUSION Concept Design: 

FUSION Concept Design Each section of the fixture is sized to fit on a single skid for ease of shipment

FUSION Concept Design: 

FUSION Concept Design Completed fixtures are assembled with a minimum of labour at each store location

FUSION Concept Design: 

FUSION Concept Design Complete fixture is ready for use 1 day after arrival at the store

FUSION Concept Design: 

FUSION Concept Design Complete service documents are created for each fixture to facilitate support via the FUSION tech support phone line

Recent FUSION Projects: 

Recent FUSION Projects

The Car Audio Pod: 

The Car Audio Pod Developed to create an all encompassing mobile entertainment experience for Best Buy, the premier electronics retailer in the USA

Mobile Audio Pod Overview: 

Mobile Audio Pod Overview All encompassing Audio Experience – Front, Rear and Subs all in one fixture Fixture has the ability to mix and match any product with any other product to demonstrate the system as it would be experienced in a vehicle

Mobile Audio Pod Construction: 

Mobile Audio Pod Construction Amplifiers are mounted on perforated aluminium panels, allowing infinite product changes without showing wear Speaker mounting panels are cut from self healing high density polyethylene plastic, allowing dozens of speaker removals and remounting before needing replacement TouchScreen System Control Vehicle fit chart database built in to software highlights valid product based on customer vehicle selection, products that will fit the vehicle are identified by blinking product selection buttons Software has the ability to “drill down” by feature; lights are turned out on products that lack the features selected by the customer

Mobile Audio Pod Key Features: 

Mobile Audio Pod Key Features Over 600 pods have been successfully deployed across the USA and Canada

Mobile Audio Pod Additional Features: 

Mobile Audio Pod Additional Features All panels mount into metal frames to insure constant panel alignment; all panels are recessed into frames, preventing damage to panel edges and maintaining a professional appearance Raised floor in the center of the pod allows for wiring to pass from front to back without requiring any conduit or floor cutting to install Built in access panels allow for easy servicing of all electronic and computer systems Pod is completely free standing with space for additional merchandising on all exterior surfaces Custom built 100 amp power supply requires only a standard mains socket, no custom electrical wiring is required Computers are updated via network or utilizing DVD disks

Our Partners: 

Our Partners

Phoenix Fixtures: 

Phoenix Fixtures Our manufacturing partner, located in Roberts, Wisconsin 15,000 Square Meter manufacturing and assembly facility CNC automated fixture manufacturing Solid Works CAD design studio 100-160 Staff Members, dependant upon demand

FUSION “All-In-One Systems”: 

FUSION “All-In-One Systems”

Slide24: 

All-In-One Demonstration Kits- Car Audio Range: FS-CA4, FS-CA6 and FS-CA8 (known as ‘Main Modules’)- These kits are truly ‘All-In-One’, allowing multiple Head Units, multiple Speakers (configured as Fronts, Rears and Subs), multiple Amps (configured also as Fronts, Rears and Subs) to be compared A full compliment of expansion boards allows adding an almost infinite amount of product to each system Aimed at the “do it yourself” shop owner who will be building their own displays and needs switching to complete the fixture