logging in or signing up Chemical Vapour Deposition krish1319 Download Post to : URL : Related Presentations : Let's Connect Share Add to Flag Embed Email Send to Blogs and Networks Add to Channel Copy embed code: Embed: Flash iPad Dynamic Copy Does not support media & animations Automatically changes to Flash or non-Flash embed WordPress Embed Customize Embed URL: Copy Thumbnail: Copy The presentation is successfully added In Your Favorites. Views: 103 Category: Education License: All Rights Reserved Like it (0) Dislike it (0) Added: May 06, 2013 This Presentation is Public Favorites: 0 Presentation Description No description available. Comments Posting comment... Premium member Presentation Transcript CHEMICAL VAPOUR DEPOSITION: BY KRISHNAN.P 2009507017 CHEMICAL VAPOUR DEPOSITIONINTRODUCTION: Chemical Vapour Deposition (CVD) is a chemical process used to produce high purity, high performance solid materials. In a typical CVD process, the substrate is exposed to one or more volatile precursors which react and decompose on the substrate surface to produce the desired deposit. During this process, volatile by-products are also produced, which are removed by gas flow through the reaction chamber. INTRODUCTIONSTEPS INVOLVED IN CHEMICAL VAPOUR DEPOSITION: STEPS INVOLVED IN CHEMICAL VAPOUR DEPOSITIONSCHEMATIC DIAGRAM - THE STEPS INVOLVED IN CVD: SCHEMATIC DIAGRAM - THE STEPS INVOLVED IN CVDTYPES OF CVD: CVD’s are classified into two types on the basis of Operating Pressure. 1. Atmospheric Pressure CVD 2. Low Pressure CVD Plasma Enhanced CVD Photochemical Vapour Deposition Thermal CVD TYPES OF CVDATMOSPHERIC PRESSURE CHEMICAL VAPOUR DEPOSITION: CASE 1 : HIGH TEMPERATURE This process is used to deposit Silicon and compound films or hard metallurgical coatings like Titanium Carbide and Titanium Nitride. CASE 2 : LOW TEMPERATURE Many insulating film layers such as Silicon dioxide need to be deposited at low temperatures for effective deposition. ATMOSPHERIC PRESSURE CHEMICAL VAPOUR DEPOSITIONCONTINUED..: Aluminium oxide films are deposited by this method from aluminium trichloride, argon and oxygen gas mixtures at temperatures ranging from 800-1000 degree Celsius The films have low chlorine content, which continue to decrease with increasing temperature. Analysis of the film growth rate on the substrates revealed that, the growth takes place only by diffusion from 800 to 950 degree Celsius and only by gas phase reaction at 1000 degree Celsius. CONTINUED..CONVEYOR BELT - APCVD: CONVEYOR BELT - APCVDLIMITATIONS OF APCVD: Film thickness uniformity cannot be maintained. Large number of pinhole defects can occur. Wafer (Substrate) throughput is low due to low deposition rate. The deposits get contaminated very easily since it takes place at atmospheric pressure. Maintaining stochiometry is extremely difficult. LIMITATIONS OF APCVDLOW PRESSURE CVD: The deposition of Silicon carbide thin film is performed using low pressure CVD of Dichlorosilane / Acetylene / Hydrogen reaction system. The Silicon carbide film deposited at three different temperatures has three different properties. LOW PRESSURE CVD 1023 K AMORPHOUS 1073 K MICROCRYSTALLINE 1173 K PREFERENTIALLY ORIENTEDCONTINUED..: This technique permits either horizontal or vertical loading of the wafers into the furnace and accommodates a large number of wafers for processing. The process results in the deposition of compounds with excellent purity and uniformity. However the technique requires higher temperatures and the deposition rate is low. CONTINUED..PLASMA ENHANCED CVD: Plasma-enhanced chemical vapor deposition (PECVD) is a process used to deposit thin films from a gas state (vapor) to a solid state on a substrate. Chemical reactions are involved in the process, which occur after creation of a plasma of the reacting gases. The plasma is generally created by RF (AC) frequency or DC discharge between two electrodes, the space between which is filled with the reacting gases. The helping hand of the Plasma helps in increasing the film quality at low temperature and pressure. PLASMA ENHANCED CVDCONTINUED..: PECVD uses electrical energy which is transferred to the gas mixture. This transforms the gas mixture into reactive radicals, ions, neutral atoms and molecules, and other highly excited species. These atomic and molecular fragments interact with a substrate and, depending on the nature of these interactions, either etching or deposition processes occur at the substrate. Some of the desirable properties of PECVD films are good adhesion, low pinhole density and uniformity. CONTINUED..SCHEMATIC DIAGRAM OF PECVD: SCHEMATIC DIAGRAM OF PECVDREACTORS USED IN PECVD: REINBERG TYPE REACTOR (DIRECT): Reactants, by-products, substrates and plasma are in the same space. Capacitive-coupled Radio Frequency plasma. Rotating substrates are present. DOWNSTREAM REACTOR (INDIRECT): Plasma is generated in a separate chamber and is pumped into the deposition chamber. Allows better control of purity and film quality when compared to the Direct type. REACTORS USED IN PECVDPHOTOCHEMICAL VAPOUR DEPOSITION: Al thin films are deposited via photochemical vapour deposition on catalytic layers of Ti, TiO 2 , and Pd, using dimethyl aluminum hydride. Deposition is carried out at low gas pressures to induce a surface reaction based on adsorption and subsequent decomposition of adsorbates. Of these three layers Ti is so effective as a catalyst that the Al films are thermally deposited even at a low substrate temperature of 60°C with a growth rate of 0.5 nm/min. PHOTOCHEMICAL VAPOUR DEPOSITIONCONTINUED..: The UV light generated by a deuterium lamp helped increase the growth rates. On the other hand, Al could be deposited on TiO 2 layers only under irradiation at a substrate temperature of 120°C It takes several minutes to cover the TiO 2 surface with Al and initiate the Al film's growth. Here, the UV light inhibited the Al growth on the surface, whereas the films are deposited thermally. X-ray photoelectron spectroscopy showed the formation of a photolytic production of the adsorbate, which acts presumably as a center that inhibits further Al growth. CONTINUED..THERMAL CVD: In thermal CVD process, temperatures as high as 2000 degree Celsius is needed to deposit the compounds. There are two basic types of reactors for thermal CVD. Hot wall reactor Cold wall reactor A hot wall reactor is an isothermal surface into which the substrates are placed. Since the whole chamber is heated, precise temperature control can be achieved by designing the furnace accordingly. THERMAL CVDCONTINUED..: A disadvantage of the hot wall configuration is that deposition occurs on the walls of the chamber as well as on the substrate. As a consequence, hot wall reactors must be frequently cleaned in order to reduce contamination of substrates. In a cold wall reactor, only the substrate is heated. The deposition takes place on the area of the highest temperature, since CVD reactions are generally endothermic. CONTINUED..CONTINUED..: The deposition is only on the substrate in cold wall reactors, and therefore contamination of particles is reduced considerably. However, hot wall reactors have higher throughput since the designs can easily accommodate multiple wafer (substrate) configurations. CONTINUED..ADVANTAGES OF CHEMICAL VAPOUR DEPOSITION: Variable shaped surfaces, given reasonable access to the coating powders or gases, such as screw threads, blind holes or channels or recesses, can be coated evenly without build-up on edges. Versatile –any element or compound can be deposited. High Purity can be obtained. High Density – nearly 100% of theoretical value. Material Formation well below the melting point Economical in production, since many parts can be coated at the same time. ADVANTAGES OF CHEMICAL VAPOUR DEPOSITIONAPPLICATIONS OF CHEMICAL VAPOUR DEPOSITION: CVD has applications across a wide range of industries such as: Coatings – Coatings for a variety of applications such as wear resistance, corrosion resistance, high temperature protection, erosion protection and combinations thereof. Semiconductors and related devices – Integrated circuits, sensors and optoelectronic devices Dense structural parts – CVD can be used to produce components that are difficult or uneconomical to produce using conventional fabrication techniques. Dense parts produced via CVD are generally thin walled and maybe deposited onto a mandrel or former. APPLICATIONS OF CHEMICAL VAPOUR DEPOSITIONCONTINUED..: Optical Fibres – For telecommunications. Composites – Preforms can be infiltrated using CVD techniques to produce ceramic matrix composites such as carbon-carbon, carbon-silicon carbide and silicon carbide-silicon carbide composites. This process is sometimes called chemical vapour infiltration or CVI. Powder production – Production of novel powders and fibres Catalysts Nanomachines CONTINUED..THANK YOU !!!: THANK YOU !!! You do not have the permission to view this presentation. In order to view it, please contact the author of the presentation.