# Heat Exchanger lecture (3)

Views:

## Presentation Description

No description available.

## Presentation Transcript

### Heat Transfer/Heat Exchanger :

Heat Transfer/Heat Exchanger How is the heat transfer? Mechanism of Convection Applications . Mean fluid Velocity and Boundary and their effect on the rate of heat transfer. Fundamental equation of heat transfer Logarithmic-mean temperature difference. Heat transfer Coefficients. Heat flux and Nusselt correlation Simulation program for Heat Exchanger

### How is the heat transfer? :

How is the heat transfer? Heat can transfer between the surface of a solid conductor and the surrounding medium whenever temperature gradient exists. Conduction Convection Natural convection Forced Convection

### Slide 3:

Natural and forced Convection Natural convection occurs whenever heat flows between a solid and fluid, or between fluid layers. As a result of heat exchange Change in density of effective fluid layers taken place, which causes upward flow of heated fluid. If this motion is associated with heat transfer mechanism only, then it is called Natural Convection

### Slide 4:

Forced Convection If this motion is associated by mechanical means such as pumps, gravity or fans, the movement of the fluid is enforced. And in this case, we then speak of Forced convection.

### Heat Exchangers :

Heat Exchangers A device whose primary purpose is the transfer of energy between two fluids is named a Heat Exchanger.

### Applications of Heat Exchangers :

Applications of Heat Exchangers Heat Exchangers prevent car engine overheating and increase efficiency Heat exchangers are used in Industry for heat transfer Heat exchangers are used in AC and furnaces

### Slide 7:

The closed-type exchanger is the most popular one. One example of this type is the Double pipe exchanger. In this type, the hot and cold fluid streams do not come into direct contact with each other. They are separated by a tube wall or flat plate.

### Principle of Heat Exchanger :

Principle of Heat Exchanger First Law of Thermodynamic: “Energy is conserved.”

### Slide 9:

Th Ti,wall To,wall Tc Region I : Hot Liquid-Solid Convection NEWTON’S LAW OF CCOLING Region II : Conduction Across Copper Wall FOURIER’S LAW Region III: Solid – Cold Liquid Convection NEWTON’S LAW OF CCOLING THERMAL BOUNDARY LAYER Energy moves from hot fluid to a surface by convection, through the wall by conduction, and then by convection from the surface to the cold fluid.

### Slide 10:

Velocity distribution and boundary layer When fluid flow through a circular tube of uniform cross-suction and fully developed, The velocity distribution depend on the type of the flow. In laminar flow the volumetric flowrate is a function of the radius. V = volumetric flowrate u = average mean velocity

### Slide 11:

In turbulent flow, there is no such distribution. The molecule of the flowing fluid which adjacent to the surface have zero velocity because of mass-attractive forces. Other fluid particles in the vicinity of this layer, when attempting to slid over it, are slow down by viscous forces. r Boundary layer

### Slide 12:

Accordingly the temperature gradient is larger at the wall and through the viscous sub-layer, and small in the turbulent core. The reason for this is 1) Heat must transfer through the boundary layer by conduction. 2) Most of the fluid have a low thermal conductivity (k) 3) While in the turbulent core there are a rapid moving eddies, which they are equalizing the temperature. heating cooling Tube wall

### Region I : Hot Liquid – Solid Convection :

Region I : Hot Liquid – Solid Convection Region II : Conduction Across Copper Wall Region III : Solid – Cold Liquid Convection U = The Overall Heat Transfer Coefficient [W/m.K]

### Calculating U using Log Mean Temperature :

Calculating U using Log Mean Temperature Hot Stream : Cold Stream: Log Mean Temperature

### Slide 15:

CON CURRENT FLOW COUNTER CURRENT FLOW Log Mean Temperature evaluation

### Slide 17:

DIMENSIONLESS ANALYSIS TO CHARACTERIZE A HEAT EXCHANGER Further Simplification: Can Be Obtained from 2 set of experiments One set, run for constant Pr And second set, run for constant Re

### Slide 18:

For laminar flow Nu = 1.62 (Re*Pr*L/D) Empirical Correlation Good To Predict within 20% Conditions: L/D > 10 0.6 < Pr < 16,700 Re > 20,000 For turbulent flow

### Experimental :

Experimental Apparatus Two copper concentric pipes Inner pipe (ID = 7.9 mm, OD = 9.5 mm, L = 1.05 m) Outer pipe (ID = 11.1 mm, OD = 12.7 mm) Thermocouples placed at 10 locations along exchanger, T1 through T10 Hot Flow Rotameters Temperature Indicator Cold Flow rotameter Heat Controller Switch for concurrent and countercurrent flow Temperature Controller

### Examples of Exp. Results :

Examples of Exp. Results Theoretical trend y = 0.8002x – 3.0841 Experimental trend y = 0.7966x – 3.5415 Theoretical trend y = 0.3317x + 4.2533 Experimental trend y = 0.4622x – 3.8097 Theoretical trend y = 0.026x Experimental trend y = 0.0175x – 4.049 Experimental Nu = 0.0175Re0.7966Pr0.4622 Theoretical Nu = 0.026Re0.8Pr0.33

### Slide 22:

Effect of core tube velocity on the local and over all Heat Transfer coefficients