Chapter 3-Dielectric properties(2)

Dielectric Properties of Ceramics:

Dielectric Properties of Ceramics EBB 443 Dr. Sabar D. Hutagalung School of Materials & Mineral Resources Engineering, Universiti Sains Malaysia

Introduction:

Introduction Dielectric materials: high electrical resistivities, but an efficient supporter of electrostatic fields. Can store energy/charge. Able to support an electrostatic field while dissipating minimal energy in the form of heat. The lower the dielectric loss (proportion of energy lost as heat), the more effective is a dielectric material. Another consideration is the dielectric constant , the extent to which a substance concentrates the electrostatic lines of flux.

Dielectric Constant:

Dielectric Constant The capacitance, C , of a capacitor formed by two parallel plates of area A spaced d apart with the area between the plates filled with dielectric material with a relative dielectric constant of ε is:

Dielectric Loss:

Dielectric Loss For a lossy (imperfect) dielectric the dielectric constant can be represented by a complex relative dielectric constant: The imaginary part of this complex dielectric constant, ε at a frequency, ω is equivalent to a frequency-dependent conductivity, σ(ω), given by:

Dielectric Loss:

ε " is also known as the loss factor . The small difference in phase from ideal behaviour is defined by an angle δ , defined through the equation tan δ is known as the loss tangent or dissipation factor . A quality factor, Q , for the dielectric is given by the reciprocal of tan δ . Dielectric Loss

Slide 6:

Equivalent circuit diagrams: (a) capacitive cell, (b) charging and loss current, (c) loss tangent for a typical dielectric Dielectric Loss

Dielectric Loss:

From Q =   o AV/d = CV If V being sinusoidal, total charge Q may be written as Current flow on discharge of the capacitive cell in time, t : For a real dielectric the current I has vector components I C and I R : I = I C + I R Dielectric Loss

Dielectric Loss:

From magnitude of these currents, also we can define a dissipation factor, tan , as Quality factor Q is: Dielectric Loss

Alternating Current Theory :

Alternating Current Theory Impedance of a resistance = R Impedance of a capacitance = 1/i ω C Mean power, P , dissipated over a cycle in a lossy capacitor with plates of area A separated by a distance d :

Dielectric Strength:

Dielectric Strength Dielectric materials are insulators (conduction cannot generally occur). However, under certain conditions, dielectric materials can break down and conduct a significant current. Generally, the lattice of a dielectric has sufficient strength to absorb the energy from impacting electrons that are accelerated by the applied electric field. However, under a sufficiently large electric field, some electrons present in the dielectric will have sufficient kinetic energy to ionize the lattice atoms causing an avalanching effect. As a result, the dielectric will begin to conduct a significant amount of current.

Dielectric Strength:

Dielectric Strength This phenomenon is called dielectric breakdown and the corresponding field intensity is referred to as the dielectric breakdown strength. Dielectric strength may be defined as the maximum potential gradient to which a material can be subjected without insulating breakdown, that is where DS is the dielectric strength in kV/mm, V B the breakdown voltage , and d the thickness.

Current-voltage characteristic up to breakdown for a typical dielectric materials:

Current-voltage characteristic up to breakdown for a typical dielectric materials

Dielectric Strength:

Dielectric Strength Dielectric strength depends on material homogeneity, specimen geometry, electrode shape and disposition, stress mode (ac, dc or pulsed) and ambient condition .

Capacitors:

Capacitors Tantalum capacitor

Capacitors:

Capacitors The basic formula for the capacitance of a parallel-plate capacitor is: To increase C, one either increases , increases A , or decreases d . Early capacitors consisted of metal foils separated by wax (  ~ 2.5), mica (  ~ 3 - 6), steatite (  ~ 5.5 - 7.5), or glass (  ~ 5 - 10). The use of titania provided a significant increase (  ~ 170), was followed by perovskite-based, such as BaTiO 3 (  ~ 1000).

Capacitors:

Capacitors C = "capacitance" = q / D V Units: Coulomb/Volt = Farad (F) ----------------------------- The capacitance of a capacitor is constant; if q increases, D V increases proportionately. Michael Faraday (1791-1867)

Capacitors:

Capacitors

Capacitors:

Capacitors DRAM chips currently utilize capacitors with Si 3 N 4 or SiO 2 as dielectric materials. The electrodes are made of doped Si or poly-Si. Capacitors can be fabricated onto IC chips. They are commonly used in conjunction with transistors in DRAM. The capacitors help maintain the contents of memory. Because of their tiny physical size, these components have low capacitance. They must be recharged thousands of times per second or the DRAM will lose its data.

Slide 19:

Q = CV Q : charge (Coulomb) C : capacitance (Farad) V : potential difference (Volt) d : separation/thickness (meter)  o : permitivity of vacuum = 8.854x10 -12 C 2 /m 2 or F/m  r : dielectric constant

Multilayer Ceramic Capacitor:

Multilayer Ceramic Capacitor The multilayer ceramic capacitor (MLCC): where N is the number of stacked plates. Ideally, the dielectric should have a low electrical conductivity so that the leakage current is not too large.

Multilayer Ceramic Capacitor:

Multilayer Ceramic Capacitor Cut-away view of multilayer ceramic capacitor. Ceramic surface-mount capacitors.

High-K Dielectric:

High-K Dielectric The bit count of MOS DRAM devices is continuously increasing. However, as bit count goes up, capacitor cell area goes down. The capacitance per cell must remain in the 25-30 fF range, which means the capacitance density must increase. One approach for DRAM manufacturing is to replace the traditional silicon nitride + silicon oxide with a higher dielectric constant ( k ) such as tantalum pentoxide (Ta 2 O 5 ), Hf-oxide (HfO 2 ) and Zr-oxide (ZrO 2 ).

Slide 23:

The roadmap of capacitor with DRAM technology. D.-S. Yoon et al. / Progress in Materials Science 48 (2003) 275–371

High-K Dielectric:

High-K Dielectric High-k dielectric films are anticipated to be required for certain applications with low power and leakage current specifications. High-k materials should be compatible with conventional industry standard MOSFET process flows using a poly-Si gate electrode. HfO 2 , ZrO 2 , and Ta 2 O 5 as high-k gate-dielectrics.

HfO2/Poly-Si high-k transistor:

HfO 2 /Poly-Si high-k transistor

ZrO2/Poly-Si high-k transistors:

ZrO 2 /Poly-Si high-k transistors

Typical material stack used in aTa2O5 DRAM capacitor:

Typical material stack used in aTa 2 O 5 DRAM capacitor

A Review of High High-k Dielectrics:

A Review of High High-k Dielectrics Gate dielectric materials having high dielectric constant, large band gap with a favorable band alignment, low interface state density and good thermal stability are needed for future gate dielectric applications. Ultra high-k materials such as STO (SrTiO3) or BST (BaSrTiO3) may cause fringing field induced barrier lowering effect.

Slide 29:

High-k gate dielectrics have a number of difficulties: (1) crystallization upon heating, (2) dopant penetration, (3) fixed charge, (4) low channel mobility and (5) uncontrolled oxide formation at the Si/high-k interface. A Review of High High-k Dielectrics

High-K Problems:

High-K Problems

High-K and PolySi are Incompatible:

High-K and PolySi are Incompatible

Phonon Scattering in High-K:

Phonon Scattering in High-K

The Gate Stack:

The Gate Stack Schematic illustration of important regions in a CMOS FET gate stack Expected performance trends for complementary metal oxidesemiconductor (CMOS) transistor technologies. The unrelenting reduction in transistor size and the associated decrease in gate delay for (a) an NMOS transistor and (b) a PMOS FET are evident.

Slide 34:

Schematic image of MOS transistors in the year 2003 and 2013. EOT- equivalent oxide thickness

Slide 35:

Physical and electrical thickness of high-k gate dielectric (ideal). SiO 2 equivalent thickness EOT is smaller than high-k physical thickness.

Slide 36:

The depletion region of thickness W d forms adjacent to the poly-Si/oxide interface.

Slide 37:

For example, if the capacitor dielectric is SiO 2 , t eq = 3.90 e o ( A/C ), e o = 8.85x10 -3 fF/ m m, thus a capacitance density of C / A= 34.5 fF /m m 2 corresponds to t eq =10 Å . A dielectric with a relative permittivity of 16 results in a physical thickness of ~40 Å, to obtain t eq =10 Å .

Slide 38:

Comparison of (a) stacked and (b) single-layer gate dielectrics in a hypothetical transistor gate stack. Either structure results in the same overall gate stack capacitance or equivalent oxide thickness, t eq =10 Å.