Characterization of Biofield Energy Treated N,N-Dimethylformamide

Views:
 
     
 

Presentation Description

The current study aimed was to investigates the impact of biofield energy treatment on physical and spectral properties of N,N-Dimethylformamide using various analytical techniques.

Comments

Presentation Transcript

slide 1:

American Journal of Applied Chemistry 2015 36: 188-193 Published online November 9 2015 http://www.sciencepublishinggroup.com/j/ajac doi: 10.11648/j.ajac.20150306.12 ISSN: 2330-8753 Print ISSN: 2330-8745 Online Chromatographic Spectroscopic and Thermal Characterization of Biofield Energy Treated NN-Dimethylformamide Mahendra Kumar Trivedi 1 Alice Branton 1 Dahryn Trivedi 1 Gopal Nayak 1 Gunin Saikia 2 Snehasis Jana 2 1 Trivedi Global Inc. Henderson NV USA 2 Trivedi Science Research Laboratory Pvt. Ltd. Bhopal Madhya Pradesh India Email address: publicationtrivedisrl.com S. Jana To cite this article: Mahendra Kumar Trivedi Alice Branton Dahryn Trivedi Gopal Nayak Gunin Saikia Snehasis Jana. Chromatographic Spectroscopic and Thermal Characterization of Biofield Energy Treated NN-Dimethylformamide. American Journal of Applied Chemistry. Vol. 3 No. 6 2015 pp. 188-193. doi: 10.11648/j.ajac.20150306.12 Abstract: NN-Dimethylformamide DMF is a ‘universal’ solvent and has wide variety of applications in organic synthesis purification crystallization and as cross-linking agent. The aim of this study was to evaluate the physicochemical and spectroscopic properties of DMF after the biofield energy treatment using various analytical techniques. DMF sample was divided into two parts one part control remained as untreated while the other treated part was treated with Mr. Trivedi’s biofield energy treatment. The treated sample was subdivided into three parts named as T1 T2 and T3 for gas chromatography-mass spectrometry GC-MS analysis. Five relatively intense peaks were observed in the mass spectrum of both control and treated samples of DMF. The GC-MS data revealed that the isotopic abundance ratio of PM+1/PM in DMF was slightly decreased by 5.76 in T1 and increased by 48.73 and 30.17 in T2 and T3 samples respectively as compared to the control where PM- primary molecule PM+1- isotopic molecule either for 13 C or 2 H or 15 N. Similarly the isotopic abundance ratio of PM+2/PM was decreased by 10.34 in T1 and then increased upto 43.67 T2 as compared to the control where PM+2- isotopic molecule for 18 O. In high performance liquid chromatography HPLC the treated DMF showed similar retention time T R as compared to the control with an additional small peak at 2.26 min appeared in the treated sample. In DSC thermogram the heat change in a sharp endothermic transition at around 61°C of treated DMF was increased by 152.56 as compared to the control. Further CO and C-N stretching frequencies of treated sample were shifted by 7 cm -1 and 3 cm -1 respectively towards low energy region in Fourier transform infrared FT-IR spectroscopy. These results suggested that biofield energy treatment has significantly altered the physical and spectroscopic properties of DMF which could make them more stable solvent in organic synthesis and as a suitable formulation agent in polymer/paint industry. Keywords: Biofield Energy Treatment NN-Dimethylformamide Gas Chromatography-Mass Spectrometry / High Performance Liquid Chromatography Isotopic Abundance 1. Introduction NN-Dimethylformamide DMF is a colorless organic liquid with slight amine odor. It is a highly polar aprotic solvent extensively used in the organic synthesis 1 paint and coating formulations 2. Its attractive solvent properties are due to the high dielectric constant wide solubility range and less volatile nature. The high solubility of polyacrylonitrile in DMF 3 and high miscibility of DMF in water makes it the ideal solvent in acrylic fiber production. Also the synthesis of polyurethane and some other polyurethane based elastomers is performed in DMF based solvents 4. It has an important role in the synthesis of active pharmaceutical ingredients API as a solvent 5 and as a co-solvent in the crystallization of drug molecules. For instance piroxicam is soluble in DMF and after addition of a bridging liquid like chloroform enables the diffusion of the drug to a third emulsified phase in which the drug molecule agglomerates to grow spherical crystals 6. Further as a solvent DMF is used in the production of polyurethane coated textiles in the production of synthetic fibers 10 7 as

slide 2:

American Journal of Applied Chemistry 2015 36: 188-193 189 gas stabilizer in acetylene cylinders 8 in the production of medical devices 9 as cleaning solvent as laboratory chemical etc. 10. DMF is also used in epoxy based formulations 11. Despite its usabilities it has some toxic effect on the environment also. However it decomposes into dimethyl amine and formaldehyde as a result of UV irradiation or hydrolyzed in aqueous solution and at elevated temperature in the presence of alkali or acid limiting its practical applications 12. The stability issue associated with DMF can be addressed by an alternative mean. Nowadays biofield energy treatment is known to alter the various properties of living and non-living things 1314. The biofield is the energy fields that purportedly surround and penetrate the human body. Human has the ability to harness the energy from environment/universe and can transmit into any object around the Universe. After receiving the energy the object or living things used to respond in a useful way. This process is known as biofield treatment 15. National Centre for Complementary and Alternative Medicine NCCAM have reported that energy therapies are commonly used to promote the health and healing and are popular in subgroup of energy medicine among complementary medicines 1617. People in western countries practice biofield healing therapy as certain form of Complementary and Alternative Medicine CAM 18. Mr. Trivedi’s unique biofield treatment is also called as The Trivedi Effect ® . The impact of the Trivedi Effect has been well studied in various research fields like material sciences 19 20 agricultural 1421 and microbiology research 22. Hence based on the outstanding results achieved by the biofield energy treatment an attempt was made to evaluate the effect of biofield energy treatment on DMF. 2. Experimental 2.1. Materials and Method DMF was procured from Qualigens India. The compound was distributed into two groups where one part was referred as control and the other as treated group. The biofield energy treatment was received by the treated group in sealed pack from Mr. Trivedi under standard laboratory conditions. The control and treated samples were characterized using gas chromatography-mass spectrometry GC-MS high performance liquid chromatography HPLC differential scanning calorimetry DSC and Fourier transform infrared FT-IR spectroscopy. 2.2. GC-MS The GC-MS analysis was done on Perkin Elmer/auto system XL built with Turbo mass USA. The detection limit of the detector is upto 1 picogram. For GC-MS analysis the treated sample was further divided into three parts as T1 T2 and T3. The GC-MS spectrum was plotted as the abundance vs. mass to charge ratio m/z. The isotopic abundance ratio of 13 C/ 12 C or 2 H/ 1 H PM+1/PM and 18 O/ 16 O PM+2/PM was expressed by its deviation in the treated sample as compared to the control. The percentage changes in isotopic ratio PM+1/PM and PM+2/PM was calculated from the Equation 1: Percent change in isotopic abundance ratio × 100 1 Where R Treated and R Control are the ratio of intensity at PM+1 to PM in mass spectra of treated and control samples respectively. 2.3. HPLC The HPLC was performed on a Knauer High Performance Liquid Chromatograph Berlin Germany equipped with Smartline Pump 1000 and a UV 2600 detector. Chromatographic separation was performed on a C 18 column Eurospher 100 with a dimension of 250 x 4 mm and 5 µm particle size. The mobile phase used was methanol with a flow rate of 1 mL/min at 25°C. 2.4. DSC The DSC analysis was done with Perkin Elmer/Pyris-1 USA a heating rate of 10°C/min and nitrogen flow of 5 mL/min was used. The change in latent heat ∆H of control and treated ethanol was recorded from their respective DSC curves. The percent change in boiling point and latent heat of vaporization was calculated using equation 2: change × 100 2 Where T Control and T Treated are the peak point of degradation of control and treated samples respectively. 2.5. FT-IR Spectroscopy FT-IR spectra were acquired from Shimadzu’s Fourier transform infrared spectrometer Japan in the frequency region of 500-4000 cm -1 . The samples were prepared by mixing with spectroscopic grade KBr into fine powder and then pressed into pellets. 3. Results and Discussion 3.1. GC-MS Analysis The mass spectra of control and treated samples T1 T2 and T3 are showed in Figure 1. There were five major peaks observed in the control sample i.e. at m/z 73 58 44 28 and 18. These peaks mainly due to DMF molecular ion peak and fragmented peaks of the following ions: C 3 H 7 NO + C 2 H 4 NO + CH 2 NO + CH 2 N + and NH 4 + respectively. Mass spectra showed PM peak at m/z 73 in control and all the treated samples of DMF at same intensity. The GC-MS spectra of control DMF is well matched with the reported literature 23. The treated samples T1 T2 and T3 were fragmented and appeared in the mass spectra with different intensities except PM as compared to the control.

slide 3:

190 Mahendra Kumar Trivedi et al.: Chromatographic Spectroscopic and Thermal Characterization of Biofield Energy Treated NN-Dimethylformamide Figure 1. GC-MS spectra of control and treated samples of DMF . There was a significant alteration observed in isotopic abundance ratio of PM+1/PM and PM+2/PM in treated DMF samples as compared to the control. The change in isotopic abundance ratio of PM+1/PM and PM+2/PM for the treated samples are shown in Figure 2. The isotopic abundance ratio of PM+1/PM of treated DMF was increased by 48.73 in T2 and 30.17 in T3 and slightly decreased by 5.76 in T1 as compared to the control. Similarly the isotopic abundance ratio of PM+2/PM was increased by 43.67 in T2 and 34.48 in T3 while decreased by 10.34 in T1. It was observed that the isotopic abundance ratio of PM+1/PM and PM+2/PM in treated samples have followed the same trend of increasing ratios of heavier isotopes. The increased number of heavier isotopes 13 C or 2 H or 15 N in treated DMF samples may increase the effective mass µ of the bond 24. Atoms in a chemical bond with higher isotopic number have higher binding energy with increased effective mass µ and vice versa. Increased effective mass may be responsible for the higher binding energy after biofield energy treatment. The isotopic abundance ratios were depleted slightly in T1. As the depletion or enrichment of the heavier isotopes in a molecule occurred due to the biofield energy treatment is assumed to be a kinetically driven process 25. On the other hand the enhancement of heavier isotopes in T2 and T3 samples are assumed to be localized enrichment which may lead to significant change in energy of the isotope-substituted bonds. It may enhance the bond strength stability and binding energy of DMF. Figure 2. Percent change in isotopic abundance ratio of PM+1/PM and PM+1/PM in DMF under biofield energy treatment. 3.2. HPLC Analysis Figure 3. HPLC chromatograms of control and treated sample of DMF . In the HPLC chromatogram the intensity vs. retention time of control and treated DMF is plotted as shown in Figure 3 of control and treated DMF. The control sample showed a single peak in the chromatogram while two separate peaks were observed in the chromatogram of the treated sample. The retention time T R of control sample was 2.41 min with relative intensity 99.86 however the T R of treated DMF showed peak at 2.26 min and 2.46 min with relative intensities 13.03 and 84.14 respectively. The slight increases in the T R of the highest intense peak may be attributed to the decreased polarity of DMF after biofield energy treatment.

slide 4:

American Journal of Applied Chemistry 2015 36: 188-193 191 The splitting of the treated DMF peak in the chromatogram is not clearly understood however this may be due to the impurity with the sample or may be from the solvent. 3.3. DSC Analysis DSC was used for thermal analysis of control and treated samples of DMF. The heat change ∆H in the DSC thermogram of control and treated samples are shown in Figure 4. There were two characteristic endothermic transitions observed at around 61-64°C and around 80-100°C in both control and treated samples of DMF. The heat absorbed around 61-64°C in the control sample was found to be 44.63 J/g but after biofield energy treatment it was found to be 112.77 J/g. The increase in absorbed heat ∆H in the treated sample was significantly increased by 152.67 as compared to the control. The increase in ∆H after biofield treatment could be due to alteration of intermolecular interaction in DMF that might increase the thermal stability of the treated sample. 3.4. FT-IR Analysis The FT-IR spectra of control and biofield energy treated DMF are showed in Figure 5. The vibrational peak at 2932 cm -1 was assigned to aliphatic C-H stretching of the methyl groups. Peaks in the range of 1689 cm -1 to 1661 cm -1 in the control and treated samples were assigned to CO stretching vibration. Figure 4. DSC thermograms of control and treated samples of DMF .

slide 5:

192 Mahendra Kumar Trivedi et al.: Chromatographic Spectroscopic and Thermal Characterization of Biofield Energy Treated NN-Dimethylformamide Figure 5. FT-IR spectra of control and treated samples of DMF . The peak at 1689 cm -1 was shifted by 7 cm -1 to 1682 cm -1 and the peak at 1663 cm -1 was shifted by 2 cm -1 to 1661 cm -1 after biofield energy treatment. In addition the peak assigned for C-N stretching at 1090 cm -1 in the control sample was shifted by 3 cm -1 to 1087 cm -1 in the treated sample of DMF. In both the cases we have observed a shift of frequencies towards the low energy region. There are two possible reasons for this to happen: force constant may be decreased or reduced mass µ may be increased or both 26. From the GC-MS analysis it was found that the number of heavier atoms increased significantly and well supported by isotopic abundance ratio. It is assumed that due to the increased isotopic abundance ratio of PM+1/PM and PM+2/PM in treated DMF the effective mass µ increased and eventually wavenumber decreased. The FT-IR results after biofield treatment as compared to the control had shown changes in structural properties of the molecule except the C-H stretching frequencies which may lead to the changes in polarity of the treated DMF sample. 4. Conclusions DMF was studied under the influence of biofield energy treatment and significant changes were observed in both physical and chemical properties of the molecule. The isotopic abundance ratio of PM+1/PM and PM+2/PM in DMF was significantly increased up to 48.73 and 43.67 respectively as compared to the control. The alteration of isotopic ratio after biofield energy treatment has a significant impact on the bond energies and the chemical stability of the molecule. The slight increase in retention time may be due to the decreased polarity of treated DMF sample as compared to the control in the HPLC chromatogram. The significant heat change during the sharp transition at 61°C in the DSC thermogram up to 152.56 also indicated the enhanced stability of the treated DMF. These results also supported by the FT-IR spectra where CO and C-N vibrational frequencies were shifted to lower energy region may be due to the increased effective masses. It is assumed from the results that the increased isotopic abundance ratio of PM+1 and PM+2 after Mr. Trivedi’s biofield energy treatment on DMF that could result in the reduction of hydrolysis and photooxidation reactions initiated at elevated temperature and in the presence of light and pH. Acknowledgements The authors would like to acknowledge the whole team from the Sophisticated Analytical Instrument Facility SAIF Nagpur for providing the instrumental facility. We are very grateful for the support from Trivedi Science Trivedi Master Wellness and Trivedi Testimonials in this research work.

slide 6:

American Journal of Applied Chemistry 2015 36: 188-193 193 References 1 Liu C Ni Q Baoa F Qiua J 2011 A simple and efficient protocol for a palladium-catalyzed ligand-free Suzuki reaction at room temperature in aqueous DMF. Green Chem 13: 1260-1266. 2 Pageau D Marcu E Aston D 2005 Paint stripping composition and method of using the same. US 6923873 B2. 3 Iovleva MM Smirnova VN Budnitskii GA 2001 The solubility of polyacrylonitrile. Fibre Chem 33: 262-264. 4 Chen TK Tien YI Wei KH 2000 Synthesis and characterization of novel segmented polyurethane/clay nanocomposites. Polymer 41: 1345-1353. 5 Grodowska K Parczewski A 2010 Organic solvents in the pharmaceutical industry. Acta Pol Pharm 67: 3-12. 6 Dixit M Kulkarni PK 2012 Lyophilization monophase solution technique for improvement of the solubility and dissolution of piroxicam. Res Pharm Sci 7: 13-21. 7 Subbiah T Bhat GS Tock RW Parameswaran S Ramkumar SS 2005 Electrospinning of nanofibers. J Appl Poly Sci 96: 557-569. 8 Stapf D Passler P Bachtler M Scheidsteger O Bartenbach B 2002 Preparation of acetylene and synthesis gas US 6365792 B1. 9 Hildenbrand K von Dohren HH Perrey H Frank G Dhein R 1989 Test device and a method for the detection of a component of a liquid sample US 4824639 A. 10 Kuo HW Lin KC Huang YS Lou JC Cheng TJ et al. 2001 Reduction of worker exposure to solvents by means of an occupational health program: An experience at a synthetic leather factory in Taiwan. J Occup Health 43: 339-345. 11 Mauerer O 2005 New reactive halogen-free flame retardant system for epoxy resins. Polym Degrad Stabil 88: 70-73. 12 Chang CP Chen JN Luc MC Yang HY 2005 Photocatalytic oxidation of gaseous DMF using thin film TiO 2 photocatalyst. Chemosphere 58: 1071-1078. 13 Trivedi MK Patil S Tallapragada RM 2014 Atomic crystalline and powder characteristics of treated zirconia and silica powders. J Material Sci Eng 3: 144. 14 Shinde V Sances F Patil S Spence A 2012 Impact of biofield treatment on growth and yield of lettuce and tomato. Aust J Basic Appl Sci 6: 100-105. 15 Rubik B 2002 The biofield hypothesis: Its biophysical basis and role in medicine. J Altern Complement Med 8: 703-717. 16 Thomas AH 2012 Hidden in plain sight: The simple link between relativity and quantum mechanics. Swansea UK. 17 NIH National Center for Complementary and Alternative Medicine. CAM Basics. Publication 347. October 2 2008. Available at: http://nccam.nih.gov/health/whatiscam/ 18 Movaffaghi Z Farsi M 2009 Biofield therapies: Biophysical basis and biological regulations Complement Ther Clin Pract 15: 35-37 31. 19 Trivedi MK Nayak G Patil S Tallapragada RM Latiyal O 2015 Studies of the atomic and crystalline characteristics of ceramic oxide nano powders after bio field treatment. Ind Eng Manage 4: 161. 20 Trivedi MK Patil S Nayak G Jana S Latiyal O 2015 Influence of biofield treatment on physical structural and spectral properties of boron nitride. J Material Sci Eng 4: 181. 21 Lenssen AW 2013 Biofield and fungicide seed treatment influences on soybean productivity seed quality and weed community. Agricultural Journal 83: 138-143. 22 Trivedi MK Patil S Shettigar H Bairwa K Jana S 2015 Phenotypic and biotypic characterization of Klebsiella oxytoca: An impact of biofield treatment. J Microb Biochem Technol 7: 203-206. 23 http://webbook.nist.gov/cgi/cbook.cgiIDC68122Mask20 0Mass-Spec 24 Rieley G 1994 Derivatization of organic-compounds prior to gas-chromatographic combustion-isotope ratio mass-spectrometric analysis: Identification of isotope fractionation processes. Analyst 119: 915-919. 25 Mook W Vries J 2003-2004 Environmental isotopes in the hydrological cycle principles and applications. International Atomic Energy Agency Vienna 1: 1-271. 26 Smith BC 2011 Fundamentals of Fourier transform infrared spectroscopy CRC Press Taylor and Francis Group Boka Raton New York.

authorStream Live Help