Basic PLC

Category: Entertainment

Presentation Description

No description available.


Presentation Transcript

Slide 1: 

1 Basic PLC

Slide 2: 

2 Description This training introduces the basic hardware and software components of a Programmable Controller (PLC). It details the architecture and basic instruction set common to all PLC’s. Basic programming techniques and logic designs are covered. This training describes the operating features of the PLC, the advantages of the PLC over hard-wired control systems, practical applications, troubleshooting and maintenance of PLC’s.

Slide 3: 

3 Objectives At the end of the training the participants should be able to: Describe the major components of a common PLC. Interpret PLC specifications. Apply troubleshooting techniques. Convert conventional relay logic to a PLC language. Operate and program a PLC for a given application.

Slide 4: 

4 Course Contents History of Programmable Controllers Relay Ladder Logic Central Processing Unit Input/Output System Programming and Peripheral Devices Programming Concepts Applications Troubleshooting and Maintenance

Slide 5: 

Advantages of PLCs Less wiring. Wiring between devices and relay contacts are done in the PLC program. Easier and faster to make changes. Trouble shooting aids make programming easier and reduce downtime. Reliable components make these likely to operate for years before failure. INTRODUCTION TO PLCS

Slide 6: 

PLC Origin - Developed to replace relays in the late 1960s - Costs dropped and became popular by 1980s - Now used in many industrial designs

Slide 7: 

7 Historical Background The Hydramatic Division of the General Motors Corporation specified the design criteria for the first programmable controller in 1968 Their primary goal To eliminate the high costs associated with inflexible, relay-controlled systems.

Slide 8: 

8 Historical Background The controller had to be designed in modular form, so that sub-assemblies could be removed easily for replacement or repair. The control system needed the capability to pass data collection to a central system. The system had to be reusable. The method used to program the controller had to be simple, so that it could be easily understood by plant personnel.

Slide 9: 

9 Programmable Controller Development 1968  Programmable concept developed 1969  Hardware CPU controller, with logic instructions, 1 K of memory and 128 I/O points 1974  Use of several (multi) processors within a PLC - timers and counters; arithmetic operations; 12 K of memory and 1024 I/O points 1976  Remote input/output systems introduced 1977  Microprocessors - based PLC introduced

Slide 10: 

10 Programmable Controller Development 1980  Intelligent I/O modules developed Enhanced communications facilities Enhanced software features (e.g. documentation) Use of personal microcomputers as programming aids 1983  Low - cost small PLC’s introduced 1985 on  Networking of all levels of PLC, computer and machine using SCADA software.

Slide 11: 

11 Programmable Logic Controllers ( Definition according to NEMA standard ICS3-1978) A digitally operating electronic apparatus which uses a programming memory for the internal storage of instructions for implementing specific functions such as logic, sequencing, timing, counting and arithmetic to control through digital or analog modules, various types of machines or process.

Slide 12: 

12 Leading Brands Of PLC AMERICAN 1. Allen Bradley 2. Gould Modicon 3. Texas Instruments 4. General Electric 5. Westinghouse 6. Cutter Hammer 7. Square D EUROPEAN 1. Siemens 2. Klockner & Mouller 3. Festo 4. Telemechanique

Slide 13: 

13 Leading Brands Of PLC JAPANESE 1. Toshiba 2. Omron 3. Fanuc 4. Mitsubishi

Slide 14: 

14 Areas of Application Manufacturing / Machining Food / Beverage Metals Power Mining Petrochemical / Chemical

Slide 15: 

15 PLC Size 1. SMALL - it covers units with up to 128 I/O’s and memories up to 2 Kbytes. - these PLC’s are capable of providing simple to advance levels or machine controls. 2. MEDIUM - have up to 2048 I/O’s and memories up to 32 Kbytes. 3. LARGE - the most sophisticated units of the PLC family. They have up to 8192 I/O’s and memories up to 750 Kbytes. - can control individual production processes or entire plant.

Slide 16: 


Slide 17: 

17 Tank Used to Mix Two Liquids A tank is used to mix two liquids. The control circuit operates as follows: 1. When the start button is pressed, solenoids A and B energize. This permits the two liquids to begin filling the tank. 2. When the tank is filled, the float switch trips. This de-energizes solenoids A and B and starts the motor used to mix the liquids together. 3. The motor is permitted to run for one minute. After one minute has elapsed, the motor turns off and solenoid C energizes to drain the tank.

Slide 18: 

4. When the tank is empty, the float switch de-energizes solenoid C. 5. A stop button can be used to stop the process at any point. 6. If the motor becomes overloaded, the action of the entire circuit will stop. 7. Once the circuit has been energized it will continue to operate until it is manually stopped. 18 Tank Used to Mix Two Liquids

Slide 19: 

19 Major Components of a Common PLC

Slide 20: 

20 Major Components of a Common PLC POWER SUPPLY Provides the voltage needed to run the primary PLC components I/O MODULES Provides signal conversion and isolation between the internal logic- level signals inside the PLC and the field’s high level signal.

Slide 21: 

21 Major Components of a Common PLC PROCESSOR Provides intelligence to command and govern the activities of the entire PLC systems. PROGRAMMING DEVICE used to enter the desired program that will determine the sequence of operation and control of process equipment or driven machine.

Slide 22: 

22 Programming Device Also known as: Industrial Terminal ( Allen Bradley ) Program Development Terminal ( General Electric ) Programming Panel ( Gould Modicon ) Programmer ( Square D ) Program Loader ( Idec-Izumi ) Programming Console ( Keyence / Omron )

Slide 23: 

23 Programming Device Types: Hand held unit with LED / LCD display Desktop type with a CRT display Compatible computer terminal

Slide 24: 

24 I/O Module The I/O interface section of a PLC connects it to external field devices. The main purpose of the I/O interface is to condition the various signals received from or sent to the external input and output devices. Input modules converts signals from discrete or analog input devices to logic levels acceptable to PLC’s processor. Output modules converts signal from the processor to levels capable of driving the connected discrete or analog output devices.

Slide 25: 


Slide 26: 


Slide 27: 


Slide 28: 


Slide 29: 


Slide 30: 


Slide 31: 


Slide 32: 

32 I/O Circuits DIFFERENT TYPES OF I/O CIRCUITS 1. Pilot Duty Outputs Outputs of this type typically are used to drive high-current electromagnetic loads such as solenoids, relays, valves, and motor starters. These loads are highly inductive and exhibit a large inrush current. Pilot duty outputs should be capable of withstanding an inrush current of 10 times the rated load for a short period of time without failure.

Slide 33: 

33 I/O Circuits 2. General - Purpose Outputs These are usually low- voltage and low-current and are used to drive indicating lights and other non-inductive loads. Noise suppression may or may not be included on this types of modules. 3. Discrete Inputs Circuits of this type are used to sense the status of limit switches, push buttons, and other discrete sensors. Noise suppression is of great importance in preventing false indication of inputs turning on or off because of noise.

Slide 34: 

34 I/O Circuits 4. Analog I/O Circuits of this type sense or drive analog signals. Analog inputs come from devices, such as thermocouples, strain gages, or pressure sensors, that provide a signal voltage or current that is derived from the process variable. Standard Analog Input signals: 4-20mA; 0-10V Analog outputs can be used to drive devices such as voltmeters, X-Y recorders, servomotor drives, and valves through the use of transducers. Standard Analog Output signals: 4-20mA; 0-5V; 0-10V

Slide 35: 

35 I/O Circuits 5. Special - Purpose I/O Circuits of this type are used to interface PLCs to very specific types of circuits such as servomotors, stepping motors PID (proportional plus integral plus derivative) loops, high-speed pulse counting, resolver and decoder inputs, multiplexed displays, and keyboards. This module allows for limited access to timer and counter presets and other PLC variables without requiring a program loader.

Slide 36: 


Slide 37: 

37 P. B SWITCH INPUT MODULE WIRING DIAGRAM LADDER PROGRAM I:2 0 I= Input Module slot # in rack Module Terminal # Allen-Bradley 1746-1A16 Address I:2.0/0

Slide 38: 


Slide 39: 

39 Discrete Input A discrete input also referred as digital input is an input that is either ON or OFF are connected to the PLC digital input. In the ON condition it is referred to as logic 1 or a logic high and in the OFF condition maybe referred to as logic o or logic low.

Slide 40: 

40 OFF Logic 0 IN PLC Input Module 24 V dc OFF Logic 1 IN PLC Input Module 24 V dc

Slide 41: 

41 Tank Level Transmitter An analog input is an input signal that has a continuous signal. Typical inputs may vary from 0 to 20mA, 4 to 20mA or 0 to10V. Below, a level transmitter monitors the level of liquid in the tank. Depending on the level Tx, the signal to the PLC can either increase or decrease as the level increases or decreases. Analog Input

Slide 42: 

42 OUT PLC Digital Output Module Lamp A discrete output is either in an ON or OFF condition. Solenoids, contactors coils, lamps are example of devices connected to the Discrete or digital outputs. Below, the lamp can be turned ON or OFF by the PLC output it is connected to. Digital Output

Slide 43: 

43 OUT PLC Analog Output Module An analog output is an output signal that has a continuous signal. Typical outputs may vary from 0 to 20mA, 4 to 20mA or 0 to10V. Analog Output E P Pneumatic control valve Supply air Electric to pneumatic transducer 0 to 10V

Slide 44: 

44 Processor The processor module contains the PLC’s microprocessor, its supporting circuitry, and its memory system. The main function of the microprocessor is to analyze data coming from field sensors through input modules, make decisions based on the user’s defined control program and return signal back through output modules to the field devices. Field sensors: switches, flow, level, pressure, temp. transmitters, etc. Field output devices: motors, valves, solenoids, lamps, or audible devices. The memory system in the processor module has two parts: a system memory and an application memory.

Slide 45: 

45 Memory Map Organization System memory includes an area called the EXECUTIVE, composed of permanently-stored programs that direct all system activities, such as execution of the users control program, communication with peripheral devices, and other system activities. The system memory also contains the routines that implement the PLC’s instruction set, which is composed of specific control functions such as logic, sequencing, timing, counting, and arithmetic. System memory is generally built from read-only memory devices. The application memory is divided into the data table area and user program area. The data table stores any data associated with the user’s control program, such as system input and output status data, and any stored constants, variables, or preset values. The data table is where data is monitored, manipulated, and changed for control purposes. The user program area is where the programmed instructions entered by the user are stored as an application control program. Data Table User Program

Slide 46: 

46 Memory Designs VOLATILE. A volatile memory is one that loses its stored information when power is removed. Even momentary losses of power will erase any information stored or programmed on a volatile memory chip. Common Type of Volatile Memory RAM. Random Access Memory(Read/Write) Read/write indicates that the information stored in the memory can be retrieved or read, while write indicates that the user can program or write information into the memory.

Slide 47: 

47 Memory Designs The words random access refer to the ability of any location (address) in the memory to be accessed or used. Ram memory is used for both the user memory (ladder diagrams) and storage memory in many PLC’s. RAM memory must have battery backup to retain or protect the stored program.

Slide 48: 

48 Memory Designs Several Types of RAM Memory: 1.MOS 2.HMOS 3.CMOS The CMOS-RAM (Complimentary Metal Oxide Semiconductor) is probably one of the most popular. CMOS-RAM is popular because it has a very low current drain when not being accessed (15microamps.), and the information stored in memory can be retained by as little as 2Vdc.

Slide 49: 

49 Memory Designs NON-VOLATILE Has the ability to retain stored information when power is removed, accidentally or intentionally. These memories do not require battery back-up. Common Type of Non-Volatile Memory ROM, Read Only Memory Read only indicates that the information stored in memory can be read only and cannot be changed. Information in ROM is placed there by the manufacturer for the internal use and operation of the PLC.

Slide 50: 

50 Memory Designs Other Types of Non-Volatile Memory PROM, Programmable Read Only Memory Allows initial and/or additional information to be written into the chip. PROM may be written into only once after being received from the PLC manufacturer; programming is accomplish by pulses of current. The current melts the fusible links in the device, preventing it from being reprogrammed. This type of memory is used to prevent unauthorized program changes.

Slide 51: 

51 Memory Designs EPROM, Erasable Programmable Read Only Memory Ideally suited when program storage is to be semi-permanent or additional security is needed to prevent unauthorized program changes. The EPROM chip has a quartz window over a silicon material that contains the electronic integrated circuits. This window normally is covered by an opaque material, but when the opaque material is removed and the circuitry exposed to ultra violet light, the memory content can be erased. The EPROM chip is also referred to as UVPROM.

Slide 52: 

52 Memory Designs EEPROM, Electrically Erasable Programmable Read Only Memory Also referred to as E2PROM, is a chip that can be programmed using a standard programming device and can be erased by the proper signal being applied to the erase pin. EEPROM is used primarily as a non-volatile backup for the normal RAM memory. If the program in RAM is lost or erased, a copy of the program stored on an EEPROM chip can be down loaded into the RAM.

Slide 53: 

53 PLC Operation Basic Function of a Typical PLC Read all field input devices via the input interfaces, execute the user program stored in application memory, then, based on whatever control scheme has been programmed by the user, turn the field output devices on or off, or perform whatever control is necessary for the process application. This process of sequentially reading the inputs, executing the program in memory, and updating the outputs is known as scanning.

Slide 54: 

54 While the PLC is running, the scanning process includes the following four phases, which are repeated continuously as individual cycles of operation:

Slide 55: 

55 PHASE 1 – Input Status scan A PLC scan cycle begins with the CPU reading the status of its inputs. PHASE 2– Logic Solve/Program Execution The application program is executed using the status of the inputs PHASE 3– Logic Solve/Program Execution Once the program is executed, the CPU performs diagnostics and communication tasks

Slide 56: 

56 PHASE 4 - Output Status Scan An output status scan is then performed, whereby the stored output values are sent to actuators and other field output devices. The cycle ends by updating the outputs.

Slide 57: 

57 As soon as Phase 4 are completed, the entire cycle begins again with Phase 1 input scan. The time it takes to implement a scan cycle is called SCAN TIME. The scan time composed of the program scan time, which is the time required for solving the control program, and the I/O update time, or time required to read inputs and update outputs. The program scan time generally depends on the amount of memory taken by the control program and type of instructions used in the program. The time to make a single scan can vary from 1 ms to 100 ms.

Slide 58: 

58 PLC Communications Common Uses of PLC Communications Ports Changing resident PLC programs - uploading/downloading from a supervisory controller (Laptop or desktop computer). Forcing I/O points and memory elements from a remote terminal. Linking a PLC into a control hierarchy containing several sizes of PLC and computer. Monitoring data and alarms, etc. via printers or Operator Interface Units (OIUs).

Slide 59: 

59 PLC Communications Serial Communications PLC communications facilities normally provides serial transmission of information. Common Standards RS 232 Used in short-distance computer communications, with the majority of computer hardware and peripherals. Has a maximum effective distance of approx. 30 m at 9600 baud.

Slide 60: 

60 PLC Communications Local Area Network (LAN) Local Area Network provides a physical link between all devices plus providing overall data exchange management or protocol, ensuring that each device can “talk” to other machines and understand data received from them. LANs provide the common, high-speed data communications bus which interconnects any or all devices within the local area. LANs are commonly used in business applications to allow several users to share costly software packages and peripheral equipment such as printers and hard disk storage.

Slide 61: 

61 PLC Communications RS 422 / RS 485 Used for longer-distance links, often between several PCs in a distributed system. RS 485 can have a maximum distance of about 1000 meters.

Slide 62: 

62 PLC Communications Programmable Controllers and Networks Dedicated Network System of Different Manufacturers

Slide 63: 

63 Specifications Several factors are used for evaluating the quality and performance of programmable controllers when selecting a unit for a particular application. These are listed below. NUMBER OF I /O PORTS This specifies the number of I/O devices that can be connected to the controller. There should be sufficient I/O ports to meet present requirements with enough spares to provide for moderate future expansion.

Slide 64: 

Selecting a PLC Criteria • Number of logical inputs and outputs. • Memory • Number of special I/O modules • Scan Time • Communications • Software

Slide 65: 

A Detailed Design Process 1. Understand the process 2. Hardware/software selection 3. Develop ladder logic 4. Determine scan times and memory requirements

Slide 66: 

66 Specifications OUTPUT-PORT POWER RATINGS Each output port should be capable of supplying sufficient voltage and current to drive the output peripheral connected to it. SCAN TIME This is the speed at which the controller executes the relay-ladder logic program. This variable is usually specified as the scan time per 1000 logic nodes and typically ranges from 1 to 200 milliseconds.

Slide 67: 

67 Specifications MEMORY CAPACITY The amount of memory required for a particular application is related to the length of the program and the complexity of the control system. Simple applications having just a few relays do not require significant amount of memory. Program length tend to expand after the system have been used for a while. It is advantageous to a acquire a controller that has more memory than is presently needed.

Slide 68: 

PLC Status Indicators Power On Run Mode Programming Mode Fault

Slide 69: 

Troubleshooting 1. Look at the process 2. PLC status lights HALT - something has stopped the CPU RUN - the PLC thinks it is OK (and probably is) ERROR - a physical problem has occurred with the PLC 3. Indicator lights on I/O cards and sensors 4. Consult the manuals, or use software if available. 5. Use programming terminal / laptop.

Slide 70: 

List of items required when working with PLCs: 1. Programming Terminal - laptop or desktop PC. 2. PLC Software. PLC manufacturers have their own specific software and license key. 3. Communication cable for connection from Laptop to PLC. 4. Backup copy of the ladder program (on diskette, CDROM, hard disk, flash memory). If none, upload it from the PLC. 5. Documentation- (PLC manual, Software manual, drawings, ladder program printout, and Seq. of Operations manual.)

Slide 71: 

Examples of PLC Programming Software: 1. Allen-Bradley – Rockwell Software RSLogix500 2. Modicon - Modsoft 3. Omron - Syswin 4. GE-Fanuc Series 6 – LogicMaster6 5. Square D- PowerLogic 6. Texas Instruments – Simatic 6. Telemecanique – Modicon TSX Micro

Slide 72: 

72 PROGRAMMING Normally Open (NO) Normally Closed (NC) Power flows through these contacts when they are closed. The normally open (NO) is true when the input or output status bit controlling the contact is 1. The normally closed (NC) is true when the input or output status bit controlling the contact is 0.

Slide 73: 

73 Coils Coils represent relays that are energized when power flows to them. When a coil is energized it causes a corresponding output to turn on by changing the state of the status bit controlling the output to 1. That same output status bit maybe used to control normally open or normally closed contact anywhere in the program.

Slide 74: 

74 Boxes Boxes represent various instructions or functions that are Executed when power flows to the box. Some of these Functions are timers, counters and math operations.

Slide 75: 

75 AND OPERATION Each rung or network on a ladder program represents a logic operation. In the rung above, both inputs A and B must be true (1) in order for the output C to be true (1). Rung A B C

Slide 76: 

76 OR OPERATION In the rung above, it can be seen that either input A or B is be true (1), or both are true, then the output C is true (1). Rung A B C

Slide 77: 

77 NOT OPERATION In the rung above, it can be seen that if input A is be true (1), then the output C is true (0) or when A is (0), output C is 1. Rung A C

authorStream Live Help