SATELLITE T.V.: SATELLITE T.V. INTRODUCTION: In this basic introduction to satellite TV (DIRECTV and Dish Network) we’ll look at how cable TV works. Television programmers sell the rights to broadcast their programming. Programmers send their programming via radio signal to satellites to be transmitted around the world. From the satellites the radio signals are sent to broadcast centers, in the case of cable television they are sent to the local head end (Local Broadcast Center) which processes the satellite signals to offer you the television programming you watch. Cable TV Companies then deliver these signals via the many miles of cable that are installed underground or on utility poles and delivered to your home for viewing. INTRODUCTION Slide 3: Now in this introduction to satellite TV let’s look at how Satellite TV works . Satellite TV companies like Dish Network and DIRECTV; basically work in the same way. They buy the rights to broadcast programming just like cable TV companies. Television programmers send this programming by radio signal to satellites and from the satellites to broadcast centers just like cable TV. However, here’s where the similarities end. Unlike cable TV companies that have broadcast centers in most cities and towns, Satellite TV companies only have a couple of broadcast centers that re-transmit the radio signals to satellites positioned above the earth and from there send the radio signals to your home. No need to dig and destroy the environment or to cut down trees to run cable lines on utility poles SATELLITE T.V.: Satellite television is television delivered by the means of communications satellite and received by an outdoor antenna, usually a parabolic mirror generally referred to as a satellite dish , and as far as household usage is concerned, a satellite receiver either in the form of an external set-top box or a satellite tuner module built into a TV set. Satellite TV tuners are also available as a card or a USB stick to be attached to a personal computer . In many areas of the world satellite television provides a wide range of channels and services, often to areas that are not serviced by terrestrial or cable providers. Direct broadcast satellite television comes to the general public in two distinct flavors - analog and digital. This necessitates either having an analog satellite receiver or a digital satellite receiver. Analog satellite television is being replaced by digital satellite television and the latter is becoming available in a better quality known as high-definition television . SATELLITE T.V. SATELLITE T.V.: SATELLITE T.V. RECEPTION Slide 6: The first satellite television signal was relayed from Europe to the Telstar satellite over North America in 1962. The first geosynchronous communication satellite , Syncom 2 , was launched in 1963. The world's first commercial communication satellite, called Intelsat I (nicknamed Early Bird), was launched into synchronous orbit on April 6, 1965. The first national network of satellite television, called Orbita , was created in Soviet Union in 1967, and was based on the principle of using the highly elliptical Molniya satellite for re-broadcasting and delivering of TV signal to ground downlink stations. The first domestic North American satellite to carry television was Canada ’s geostationary Anik 1 , which was launched in 1972.  ATS-6 , the world's first experimental educational and Direct Broadcast Satellite , was launched in 1974. The first Soviet geostationary satellite to carry Direct-To-Home television, called Ekran , was launched in 1976 TECHNOLOGY: Satellites used for television signals are generally in either naturally highly elliptical (with inclination of +/-63.4 degrees and orbital period of about 12 hours, also known as Molniya orbit ) or geostationary orbit 37,000 km (22,300 miles) above the earth’s equator . Satellite television, like other communications relayed by satellite, starts with a transmitting antenna located at an uplink facility. Uplink satellite dishes are very large, as much as 9 to 12 meters (30 to 40 feet) in diameter. The increased diameter results in more accurate aiming and increased signal strength at the satellite. The uplink dish is pointed toward a specific satellite and the uplinked signals are transmitted within a specific frequency range, so as to be received by one of the transponders tuned to that frequency range aboard that satellite. The transponder 'retransmits' the signals back to Earth but at a different frequency band (a process known as translation, used to avoid interference with the uplink signal), typically in the C-band (4–8 GHz) or K u -band (12–18 GHz) or both. The leg of the signal path from the satellite to the receiving Earth station is called the downlink TECHNOLOGY Slide 8: A typical satellite has up to 32 transponders for Ku-band and up to 24 for a C-band only satellite, or more for hybrid satellites. Typical transponders each have a bandwidth between 27 MHz and 50 MHz. Each geo-stationary C-band satellite needs to be spaced 2 degrees from the next satellite (to avoid interference). For K u the spacing can be 1 degree. This means that there is an upper limit of 360/2 = 180 geostationary C-band satellites and 360/1 = 360 geostationary K u -band satellites. C-band transmission is susceptible to terrestrial interference while K u -band transmission is affected by rain (as water is an excellent absorber of microwaves at this particular frequency). The latter is even more adversely effected by ice crystals in thunder clouds. Last not least, there will be a sun outage when the sun lines up directly behind the geostationary satellite the reception antenna is pointing to. This will happen twice a year at around midday for a two-week period and affects both the C-band and the K u -band. The line-up swamps out all reception for a few minutes due to the sun emitting microwaves on the same frequencies used by the satellite's transponders. This happens in the spring and in the fall Slide 9: The downlinked satellite signal, quite weak after traveling the great distance (see inverse-square law ), is collected by a parabolic receiving dish, which reflects the weak signal to the dish’s focal point. Mounted on brackets at the dish's focal point is a device called a feedhorn . This feedhorn is essentially the flared front-end of a section of waveguide that gathers the signals at or near the focal point and 'conducts' them to a probe or pickup connected to a low-noise block downconverter or LNB. The LNB amplifies the relatively weak signals, filters the block of frequencies in which the satellite TV signals are transmitted, and converts the block of frequencies to a lower frequency range in the L-band range. The evolution of LNBs was one of necessity and invention. The original C-Band satellite TV systems used a Low Noise Amplifier connected to the feedhorn at the focal point of the dish. The amplified signal was then fed via very expensive and sometimes 50 ohm impedance gas filled hardline coaxial cable to an indoor receiver or, in other designs, fed to a downconverter (a mixer and a voltage tuned oscillator with some filter circuitry) for downconversion to an intermediate frequency. The channel selection was controlled, typically by a voltage tuned oscillator with the tuning voltage being fed via a separate cable to the headend . But this design evolved. Slide 10: Designs for microstrip based converters for Amateur Radio frequencies were adapted for the 4 GHz C-Band. Central to these designs was concept of block downconversion of a range of frequencies to a lower, and technologically more easily handled block of frequencies ( intermediate frequency ). The advantages of using an LNB are that cheaper cable could be used to connect the indoor receiver with the satellite TV dish and LNB, and that the technology for handling the signal at L-Band and UHF was far cheaper than that for handling the signal at C-Band frequencies. The shift to cheaper technology from the 50 Ohm impedance cable and N-Connectors of the early C-Band systems to the cheaper 75 Ohm technology and F-Connectors allowed the early satellite TV receivers to use, what were in reality, modified UHF TV tuners which selected the satellite television channel for down conversion to another lower intermediate frequency centered on 70 MHz where it was demodulated. This shift allowed the satellite television DTH industry to change from being a largely hobbyist one where receivers were built in low numbers and complete systems were expensive (costing thousands of Dollars) to a far more commercial one of mass production. Direct broadcast satellite dishes are fitted with an LNBF, which integrates the feedhorn with the LNB Slide 11: In the United States, service providers use the intermediate frequency ranges of 950-2150 MHz to carry the signal to the receiver. This allows for transmission of UHF band signals along the same span of coaxial wire at the same time. In some applications, ( DirecTV AU9-S and AT-9) ranges the lower B-Band and upper 2250-3000 MHz, are used. Newer LNBFs in use by DirecTV referred to as SWM, use a more limited frequency range of 950-1800 MHz. The satellite receiver or Set-top box demodulates and converts the signals to the desired form (outputs for television, audio, data, etc.). Sometimes, the receiver includes the capability to unscramble or decrypt the received signal; the receiver is then called an Integrated receiver/decoder or IRD. The cable connecting the receiver to the LNBF or LNB should be of the low loss type RG-6 , quad shield RG-6 or RG-11, etc. RG-59 is not recommended for this application as it is not technically designed to carry frequencies above 950 MHz, but will work in many circumstances, depending on the quality of the coaxial wire Slide 12: A practical problem relating to satellite home reception is that basically an LNB can only handle a single receiver. This is due to the fact that the LNB is mapping two different polarizations - horizontal and vertical - and in the case of the K-band two different reception bands - lower and upper - to one and the same frequency band on the cable. Depending on which frequency a transponder is transmitting at and on what polarization it is using, the satellite receiver has to switch the LNB into one of four different modes in order to receive a specific desired program on a specific transponder. This is handled by the receiver using the DiSEqC protocol to control the LNB mode. If several satellite receivers are to be attached to a single dish a so-called multiswitch will have to be used in conjunction with a special type of LNB. There are also LNBs available with a multiswitch already integrated. This problem becomes more complicated when several receivers are to use several dishes (or several LNBs mounted in a single dish) pointing to different satellites STANDARDS: Analog television distributed via satellite is usually sent scrambled or unscrambled in NTSC , PAL , or SECAM television broadcast standards. The analog signal is frequency modulated and is converted from an FM signal to what is referred to as baseband . This baseband comprises the video signal and the audio subcarrier(s). The audio subcarrier is further demodulated to provide a raw audio signal. If the signal is a digitized television signal or multiplex of signals, it is typically QPSK . In general, digital television, including that transmitted via satellites, are generally based on open standards such as MPEG and DVB-S or ISDB-S . The conditional access encryption/scrambling methods include BISS , Conax , Digicipher , Irdeto , Nagravision , PowerVu , Viaccess , Videocipher , and VideoGuard . Many conditional access systems have been compromised. STANDARDS Categories of usage: There are three primary types of satellite television usage: reception direct by the viewer, reception by local television affiliates, or reception by headends for distribution across terrestrial cable systems . Direct to the viewer reception includes direct broadcast satellite or DBS and television receive-only or TVRO, both used for homes and businesses including hotels, etc. Categories of usage Direct broadcast via satellite: Direct broadcast satellite , (DBS) also known as "Direct-To-Home" can either refer to the communications satellites themselves that deliver DBS service or the actual television service. DBS systems are commonly referred to as "mini-dish" systems. DBS uses the upper portion of the K u band, as well as portions of the K a band. Modified DBS systems can also run on C-band satellites and have been used by some networks in the past to get around legislation by some countries against reception of K u -band transmissions. Most of the DBS systems use the DVB-S standard for transmission. With Pay-TV services, the datastream is encrypted and requires proprietary reception equipment. While the underlying reception technology is similar, the Pay-TV technology is proprietary, often consisting of a Conditional Access Module and smart card . This measure assures satellite television providers that only authorised , paying subscribers have access to Pay TV content but at the same time can allow free-to-air (FTA) channels to be viewed even by the people with standard equipment (DBS receivers without the Conditional Access Modules) available in the market. Direct broadcast via satellite Television receive only: The term Television receive-only , or TVRO, arose during the early days of satellite television reception to differentiate it from commercial satellite television uplink and downlink operations (transmit and receive). This was before there was a DTH satellite television broadcast industry. Satellite television channels at that time were intended to be used by cable television networks rather than received by home viewers. Satellite TV receiver systems were largely constructed by hobbyists and engineers. In 1978 Microcomm , a small company founded by radio amateur and microwave engineer H. Paul Shuch , introduced the first commercial home satellite TV receiver. These early TVRO systems operated mainly on the C band frequencies and the dishes required were large; typically over 3 meters (10 ft) in diameter. Consequently TVRO is often referred to as "big dish" or "Big Ugly Dish" (BUD) satellite television. TVRO systems are designed to receive analog and digital satellite feeds of both television or audio from both C-band and K u -band transponders on FSS -type satellites. The higher frequency K u -band systems tend to be Direct To Home systems and can use a smaller dish antenna because of the higher power transmissions and greater antenna gain. Television receive only Television receive only: TVRO systems tend to use larger rather than smaller satellite dish antennas, since it is more likely that the owner of a TVRO system would have a C-band-only setup rather than a K u band-only setup. Additional receiver boxes allow for different types of digital satellite signal reception, such as DVB/MPEG-2 and 4DTV . The narrow beam width of a normal parabolic satellite antenna means it can only receive signals from a single satellite at a time. Simulsat or the Vertex-RSI TORUS, is a quasi-parabolic satellite earthstation antenna that is capable of receiving satellite transmissions from 35 or more C- and K u -band satellites simultaneously. Television receive only Direct to home television: Many satellite TV customers in developed television markets get their programming through a direct broadcast satellite (DBS) provider. The provider selects programs and broadcasts them to subscribers as a set package. Basically, the provider’s goal is to bring dozens or even hundreds of channels to the customers television in a form that approximates the competition from Cable TV. Unlike earlier programming, the provider’s broadcast is completely digital, which means it has high picture and stereo sound quality. Early satellite television services broadcast in C-band - radio in the 3.7 GigaHertz (GHz) to 4.2 GHz frequency range. Digital broadcast satellite transmits programming in the K u frequency range (10 GHz to 14 GHz ) [ citation needed ] . Programming sources are simply the channels that provide programming for broadcast. The provider (the DTH platform) doesn’t create original programming itself. The broadcast center is the central hub of the system. At the broadcast center, the television provider receives signals from various programming sources, compresses these signals using digital compression (encryption if necessary), and sends a broadcast signal to the proper satellite Direct to home television THANK YOU: THANK YOU BY- ABHISHEK SUNIL BAFNA.