DATA MANIPULATION INSTRUCTIONS Data manipulation instructions perform operations on data and provide the computational capabilities for the computer. The data manipulation instruction in a computer are usually divided into three basic types: Arithmetic instructions Logical and Bit manipulation instructions Shift instructions.

Arithmetic Instructions::

Arithmetic Instructions: The four basic arithmetic operations are addition, subtraction, multiplication & division. Some computers have only addition &subtraction instruction .The multiplication & division must then be generated by means of Software Subroutines (Self contained sequence of instruction that perform a computational task). A list of Typical arithmetic instruction are as follows:- Increment (INC):-this instruction adds 1 to the value stored in a register or memory word. - One common characteristic of increment operations when executed in processor registers is that a binary number of all 1’s when incremented produces a result of all 0’s.

2. Decrement (DEC):-this instruction subtracts 1 from the value stored in a register or memory word. - One common characteristic of decrement operations when executed in processor registers is that a binary number of all 0’s when decremented, produces a result of all 1’s. :

2. Decrement (DEC):-this instruction subtracts 1 from the value stored in a register or memory word. - One common characteristic of decrement operations when executed in processor registers is that a binary number of all 0’s when decremented, produces a result of all 1’s. 3. Addition (ADD) 4. Subtract (SUB) 5. Multiply (MUL) 6. Divide (DIV) These instructions may be available for different types of data .it may be binary, decimal, floating-point data. The mnemonics for three add instructions that specify different data types are shown below: ADDI:- Add two binary integer numbers. ADDF:-Add two floating-point numbers. ADDD:-Add two decimal numbers in BCD.

7. Add with Carry (ADDC):- A special carry flip- flop is used to store the carry from an operation. The instruction “add with carry” performs the addition on two operands plus the value of the carry from the previous computational.:

7. Add with Carry (ADDC):- A special carry flip- flop is used to store the carry from an operation. The instruction “add with carry” performs the addition on two operands plus the value of the carry from the previous computational. 8. Subtract with borrow(SUBB):- subtracts two words and a borrow which may have resulted from a previous subtract operation. 9. Negate (2’s complement):-the negate instruction forms the 2’s complement of a number effectively.

Logical and Manipulation instructions:

Logical and Manipulation instructions They are useful for manipulating individual bits or a group of bits that represent binary-coded information. The logical instruction consider each bit of the operand separately and treat it as a boolean variable. Logical and bit manipulation instructions are as follows: 1.Clear(CLR):- the clear instruction causes the specified operand to be replaced by 0’s. 2. Complement (COM):-the complement instruction produces the 1’s complement by inverting all the bits of the operands. 3.AND(AND) 4.OR(OR) 5.Exclusive-OR(XOR) The AND,OR,XOR instructions produces the corresponding logical operations on individual bits of the operands.

6.Clear Carry (CLRC):- 7. Set Carry (SETC):- 8. Complement Carry (COMC): Individual bits such as a carry can be cleared, set,or complement with appropriate instructions. 9. Enable interrupts (EI):- 10.Disable interrupts (DI):- Flips flops that controls the interrupts facility and is either enabled or disabled by means of bit manipulation instructions.

Shift instructions:-:

Shift instructions:- Instructions to shift the content of an operand Shifts are operations in which the bits of a word are moved to the left or right. the bit shifted in a end of the word determines the type of shift used. Shift instruction may specify either Logical shifts, Arithmetic shifts ,or rotate –type operations. Instructions are as follows: Logical shift right (SHR) Logical shift LEFT(SHL) Logical shift inserts 0 to the end bit position. the end position is the leftmost bit for shift right and the rightmost bit position for the shift left.

Slide 8:

3. Arithmetic Shift right (SHRA) 4. Arithmetic Shift left (SHLA) Arithmetic shift right instruction must preserve the sign bit in leftmost position. the sign is sifted to the right together with the rest of the number, but the sign bit itself remain unchanged. 5. Rotate right( ROR) 6. Rotate left (ROL) Rotate instructions produces a circular shift. Bits shifted out at one end of the word are not lost as in a logical shift but are circulated back into the other end.

Slide 9:

7. Rotate right through carry (RORC) 8. Rotate left through carry (ROLC) The rotate through carry instruction transfers the carry bit into the rightmost bit position of the register, transfers the leftmost bit position into the carry , and at the same time, shifts the entire register to the left. Some computer have a multiple-field format for the shift instructions OP REG TYPE RL COUNT Op is the operation code field, REG is a register address that specify the location of the operand, TYPE is a 2-bit field specifying the four different types of shifts, RL is a 1-bit field specifying a shift right or left, COUNT is a no. of shifts.

You do not have the permission to view this presentation. In order to view it, please
contact the author of the presentation.

Send to Blogs and Networks

Processing ....

Premium member

Use HTTPs

HTTPS (Hypertext Transfer Protocol Secure) is a protocol used by Web servers to transfer and display Web content securely. Most web browsers block content or generate a “mixed content” warning when users access web pages via HTTPS that contain embedded content loaded via HTTP. To prevent users from facing this, Use HTTPS option.