VMD3-3Q-Technical-Data-Sheet

Views:
 
     
 

Presentation Description

Quiet version, VMD3Q, is available for applications that require compact size and quiet operation. Find features and specification of VMD3-3Q series actuators in detail from Venture Mfg Co.

Comments

Presentation Transcript

slide 1:

Product Data Sheet VMD3/3Q Features ◆ VMD3 features its compact design which is suitable for various applications that require limited installation space such as window opener and adjustable car driver seat. Quiet version VMD3Q is available for applications that require compact size and quiet operation. ◆ Main applications:Industrial homecare furniture ◆ Input voltage:24V dc / 12V dc ◆ Max. dynamic load:1200N push/pull ◆ Max. static load :2500N push/pull ◆ Max. current:3.5 A 12V dc ◆ Max. speed:44 mm/sec no load ◆ Stroke:50300 mm other strokes are available ◆ Factory preset limit switches not adjustable ◆ Duty cycle:25 or 1 min continuous operation in 4 min. ◆ IP protection level:IP54 Standard IP65 Optional ◆ Ambient operating temperature: -25°C +65°C ◆ Color:Aluminum grey ◆ Certified :EN 55014-1 EN55014-2 ◆ Noise level :≦70dB Normal version / ≦55dB Quiet version

slide 2:

Performance Data ◆ VMD3 ◆ VMD3Q Model No. Push/Pull Max. N Speed mm/s Current A No load Full load No load Full load 12V 24V 12V 24V VMD3-XX-05-E6/K3-XXX 150 43.9 40.0 0.8 0.4 2.0 1.0 VMD3-XX-10-E6/K3-XXX 250 27.6 26.0 0.8 0.4 2.4 1.2 VMD3-XX-20-E6/K3-XXX 500 14.6 13.5 0.8 0.4 2.6 1.3 VMD3-XX-30-E6/K3-XXX 800 9.5 9.1 0.8 0.4 2.9 1.5 VMD3-XX-40-E6/K3-XXX 1000 7.0 6.5 0.8 0.4 2.8 1.4 E6: 3000 RPM motor with 6mm double start acme screw K3: 6000 RPM motor with 3mm single start acme screw Model No. Push/Pull Max. N Speed mm/s Current A No load Full load No load Full load 12V 24V 12V 24V VMD3Q-XX-20-D3-XXX 500 5.8 3.9 0.2 0.1 1.0 0.5 VMD3Q-XX-30-D3-XXX 800 3.8 2.6 0.2 0.1 1.2 0.6 D3: 2400 RPM motor with 3mm single start acme screw 2

slide 3:

Dimensions ◆ Standard type ◆ POT type 3

slide 4:

4 Front Connector Pivot orientation of rear connector 1: Drilled hole 2: Plastic 3: Spherical rod eye 4: Plastic 1: Drilled hole 0° 90° Slot depth N/A N/A N/A 6.5 N/A Slot width N/A N/A N/A 6 N/A Diameter of pivot without bushing Ø6.4 Ø8 Ø10 Ø8 Ø10 Ø8 Ø8 Ø6.4 Ø8 Ø10 1 1 3 2 Front connector code 4 Rear connector code ◆ Hall effect sensor type

slide 5:

◆ Clamp ◆ Mounting bracket Compatibility Model T control CS1 CS2 CBT2 CB3T CB4M LD3 spec - Without positioning sensor feedback - 4-Pin Moteck F-type DIN plug Control box Product CB3T-SY CB4M-S CB4M-B - With dual Hall sensors - 6-Pin Moteck F-type DIN plug 5

slide 6:

6 With Hall effect sensor With potentiometer POT The resistance between blue and white wires increases when the actuator extends and decreases when it retracts. Y W B W B Y Actuator extends With Dual Hall effect sensor Red Black M+ M- White Yellow GND VCC GND Data 1 VCC Data 2 M+ M- GND M+ M- Data 1 VCC 100 150 200 0.3 9.7K 0.3 8.6K 0.3 9.6K Stroke mm Resistance tolerance: ±0.3KΩ 250 300 0.3 9.3K 0.3 9.3K 50 0.3 9.3K Wiring Cable Plug Standard M+ M- Note: Connect M+ to ‘+’ M- to ‘-’ of DC power to extend actuator. Power Signal Blue Data 10:1 20:1 30:1 40:1 5:1 Gear ratio 3.6 6.9 10.6 14.3 2.3 Resolution pulses/mm Red Black M+ M- White Yellow GND VCC Power Green Data 2 Blue Data 1 Signal Red Black M+ M- White Yellow GND VCC Power Blue Data 1 Signal Red Black M+ M- Power

slide 7:

Ordering Key Input voltage Type 7 Terms of Use The user is responsible for application suitability of Venture products. As ongoing improvement process continues products listed on the Venture website are subject to change without prior notice. Venture reserves the right to terminate the sales or remove any product displayed on the website or listed in its catalogues. 12: 12V DC 24: 24V DC Stroke IP Protection level Front connector Clamp Mounting bracket Rear connector Positioning feedback Motor and Spindle type K3 D3 for Quiet version only Refer to Performance Data 050: 50 mm 100: 100 mm 150: 150 mm 200: 200 mm 250: 250 mm 300: 300 mm 54: IP54 standard 65: IP65 1: Drilled hole 2: Plastic slot type 3: Spherical rod eye 4: Plastic Refer to page 4 Blank: None C: Clamp Blank: None M: Mounting bracket 1: Drilled hole Refer to page 4 Blank: None HS1: Hall effect sensor HS2: Dual Hall effect sensor POT: Potentiometer 24 10 K3 100 - 1 - - - - 1 HS2 IP54 0 C - 0 LD3 - Gear ratio 05 10 40 for normal version only 20 30 Refer to Performance Data BlankNormal version QQuiet version -

authorStream Live Help