HPE MSA 2052 Storage Datasheet

Views:
 
     
 

Presentation Description

A datasheet of HPE MSA 2052 storage, including its features, specifications, etc.

Comments

Presentation Transcript

slide 1:

HPE MSA 2052 Storage Data Sheet

slide 2:

Router-switch.com 1 Content Overview ........................................................................................................................................................................ 2 Standard Features .......................................................................................................................................................... 3 Technical Specifications ................................................................................................................................................. 9 Configuration and Order Information.......................................................................................................................... 11 Where to Buy ............................................................................................................................................................... 15 Source ........................................................................................................................................................................... 15 Contact Us Tel: +1-626-239-8066 USA / +852-3050-1066 / +852-3174-6166 Fax: +852-3050-1066 Hong Kong Email: salesrouter-switch.com Sales Inquiries

slide 3:

Router-switch.com 2 Overview The hybrid flash HPE MSA 2052 Storage system with the new Gen10 ProLiant Branding is designed for affordable application acceleration that is ideal for small and remote office deployments. But do not let the low cost fool you. The HPE MSA 2052 Storage system gives you the combination of simplicity flexibility to grow now and into the future and advanced features you may not expect to find in an entry-priced array. Start with 1.6 TB of flash capacity included and scale as needed with any combination of solid state disks SSD high-performance enterprise or lower- cost midline SAS-based drives. HPE MSA Storage has been the industry-leading entry storage Fibre Channel platform for the past eight years with nearly 500000 storage systems sold worldwide. Delivering performance in excess of 200000 IOPS the hybrid flash MSA 2052 Storage system can save you up to 40 with an all-inclusive software suite and 1.6 TB of flash capacity included. It’s seriously simple and affordable flash storage to help you get the most performance for the lowest cost. · HPE MSA 2052 performs in excess of 200000 IOPS for affordable application acceleration - Delivers 2x IOPS performance than the previous generation MSA 2042 - Save 40 on the hybrid flash MSA 2052 with all-inclusive software and 1.6 TB of SSD capacity included · Advanced data services with no experience required - Easy to install easy to use easy to maintain—no storage expertise necessary - Automated tiering dynamically responds to workload changes so you don’t have to · Keep your business running with expanded data protection features - New virtualized snapshot technology makes data protection and instant recovery a snap - Remote replication with FC and iSCSI supports affordable disaster recovery · Grow flexibly now and into the future - Data-in-place upgrades protect drive investments and eliminate data migrations - Start small and scale as needed with any combination of SSD Enterprise or Midline SAS drives Figure 1 shows the MSA 2052 enclosure.

slide 4:

Router-switch.com 3 Whats New in the MSA 2052 array family • New I/O Workload tools in the User Interface to help users benefit from tiering on the MSA. • New LDAP Support • Introducing new HPE Storage File Controllers for file services. • Introducing new support for Zerto Virtual Replication for hypervisor-based BC/DR solution Standard Features HPE MSA 2052 Storage Array Access Type Block Form Factor 2U SFF or LFF Number of controllers per array 2 Number of host ports per array 8 FC host connectivity 8/16Gb iSCSI host connectivity 1Gb or 10GbI SAS host connectivity 6/12Gb Cache per array Max Read cache per array 8TB Data read/write cache + system memory per array 16GB Pool Capacity with Large Pool Support 562 TB 512 TiB RAID Levels supported: Virtual mode RAID 1 5 6 10 Enclosures Expansion Drive Enclosures 0-7 enclosures LFF/SFF array/enclosure mixing Supported Maximum number of drives per array enclosure 24 SFF/12 LFF Maximum number of drives per drive enclosure 24 SFF/12 LFF Drive enclosure interface type 6Gb SAS Drives Maximum total HDDs per array 192 SFF / 96 LFF Maximum total SSDs per array 192 SFF / 96 LFF Max raw capacity per array enclosure 76.8 TB SFF / 144TB LFF Max raw capacity per drive enclosure 76.8 TB SFF / 144TB LFF Max raw capacity per array 614.4TB SFF / 1152TB LFF Integrated SSDs 2x800GB Mixed Use SSDs Drive Capacities SFF SSDs Mixed Use 400GB 800GB 1.6TB 3.2TB

slide 5:

Router-switch.com 4 LFF SSDs Mixed Use 400GB 800GB SFF HDDs 15K: 300GB 600GB 900GB 10K: 300GB 600GB 1.2TB 1.8TB 2.4TB 7.2K: 1.0TB 2.0TB LFF HDDs 7.2K: 2TB 4TB 6TB 8TB 10TB 12TB SEDs Encryption not supported Software Features Thin Technologies Thin Provisioning Space Reclamation Thin Rebuild Tiering Performance Tier Standard Tier Archive Tier Replication Snapshots 512 Volume Copy Remote Snaps Quality of Service Virtual Tier Affinity Bundled/Integrated Licenses Advanced Data Services LTU standard Additional Features Maximum number of volumes 512 Maximum number of snapshots 512 Maximum number of hosts 512 Maximum number of initiators 1024 Customer self-installable Yes Customer self-repairable Yes Customer self-upgradeable Yes File Services Yes HPE Storage File Controller MSA 2052 Storage Models Descriptions Part Number HPE MSA 2052 SAN Dual Controller LFF Storage Q1J02A NOTE: The MSA 2052 is a pre-configured bundle that includes an MSA 2050-branded LFF array chassis two AC power supplies two MSA 2050 SAN controllers two 800GB Mixed Use SSDs one Advanced Data Services LTU two .7m PDU cords IEC C14 and one rack-mount kit. The two 800GB SSDs are shipped integrated in the MSA 2050 array. The Advanced Data Services LTU is shipped with the MSA 2050 array and requires license activation. NOTE: SFPs not included. HPE MSA 2052 SAN Dual Controller SFF Storage Q1J03A NOTE: The MSA 2052 is a pre-configured bundle that includes an MSA 2050-branded SFF array chassis two AC power supplies two MSA 2050 SAN controllers two 800GB Mixed Use SSDs one Advanced Data Services LTU two .7m PDU cords IEC C14 and one rack-mount kit. The two 800GB SSDs are shipped integrated in the MSA 2050 array. The Advanced Data Services LTU is shipped with the MSA 2050 array and requires license activation. NOTE: SFPs not included. HPE MSA 2052 SAS Dual Controller LFF Storage Q1J30A NOTE: The MSA 2052 is a pre-configured bundle that includes an MSA 2050-branded LFF array chassis two AC power supplies two MSA 2050 SAS controllers two 800GB Mixed Use SSDs one Advanced Data Services LTU two .7m PDU cords IEC C14 and one

slide 6:

Router-switch.com 5 rack-mount kit. The two 800GB SSDs are shipped integrated in the MSA 2050 array. The Advanced Data Services LTU is shipped with the MSA 2050 array and requires license activation. NOTE: SFPs are not required for SAS Storage systems. HPE MSA 2052 SAS Dual Controller SFF Storage Q1J31A NOTE: The MSA 2052 is a pre-configured bundle that includes an MSA 2050-branded SFF array chassis two AC power supplies two MSA 2050 SAS controllers two 800GB Mixed Use SSDs one Advanced Data Services LTU two .7m PDU cords IEC C14 and one rack-mount kit. The two 800GB SSDs are shipped integrated in the MSA 2050 array. The Advanced Data Services LTU is shipped with the MSA 2050 array and requires license activation. NOTE: SFPs are not required for SAS Storage systems. All MSA 2052 models offer a common set of valuable features: · MSA 2052 storage system architecture maximizes performance · Includes MSA 2050-branded SFF or LFF array chassis depending on model · Two MSA 2050 SAN or SAS controllers - Four host ports per controller - Each SAN controller supports 8 GB FC 16 GB FC 1GbE iSCSI or 10GbE iSCSI. Host connectivity - Each SAS controller supports 6Gb and/or 12Gb SAS host connectivity · 8 GB cache per controller. · Battery-free cache backup with super capacitors and compact flash · Two .7m PDU cords IEC C14 · One rack-mount kit · Two 800GB Mixed Use SSDs · One Advanced Data Services Software Suite LTU MSA 2050 SAN Controller allows customers to create their own Combo Controller by mixing FC and iSCSI SFPs. Below are the valid configurations for mixing SFPs: Configuration Table for mixing SFPs Configuration Controller Host Port 1 SFP 1 Host Port 2 SFP 1 Host Port 3 SFP 2 Host Port 4 SFP 2 Dual SAN Controller Controller A 16Gb FC 16Gb FC None None 16Gb FC 16Gb FC 8Gb FC 8Gb FC 10GbE iSCSI 10GbE iSCSI 1GbE iSCSI 1GbE iSCSI 8Gb FC 8Gb FC None None 16Gb FC 16Gb FC 8Gb FC 8Gb FC 10GbE iSCSI 10GbE iSCSI 1GbE iSCSI 1GbE iSCSI 10GbE iSCSI 10GbE iSCSI None None 10GbE iSCSI 10GbE iSCSI 1GbE iSCSI 1GbE iSCSI

slide 7:

Router-switch.com 6 1GbE iSCSI 1GbE iSCSI None None 10GbE iSCSI 10GbE iSCSI 1GbE iSCSI 1GbE iSCSI Controller B Match Controller A Match Controller A Match Controller A Match Controller A NOTES: 1 SFP in Host Port 1 must match SFP in Host Port 2 2 SFP in Host Port 3 must match SFP in Host Port 4 All MSA 2052 models offer a common set of valuable features cont: · MSA 2052 comes standard with two 800GB flash drives which allow IT managers to accelerate application performance · The two 800GB SSDs can be optionally deployed either as read cache or as an SSD virtual disk group for tiered storage. - Deploy the two embedded SSDs as Read Cache to improve random read performance. A maximum of 2 SSD’s are supported per pool providing a maximum of 4TB of read cache per controller max 8TB of read cache per array. - Deploy the two embedded SSDs as tiered storage. The MSA 2052 can manage up to three tiers of storage: Performance tier Standard tier and Archive tier. - The Performance Auto Tiering License necessary to create an SSD virtual disk group for both read and write capabilities comes standard with all MSA 2052 models. No additional software license purchase is necessary. · The two 800GB SSDs are shipped integrated pre-installed in the array chassis. · All MSA 2052 models come standard with the Advanced Data Services ADS Software Suite LTU which includes automatic tiering 512 snapshots and remote snaps for remote replication. The Advanced Data Services LTU requires license activation. · Storage Management Utility V3 SMU. This new MSA management GUI brings a new modern look and feel to array management. · Thin Provisioning allows storage allocation of physical storage resources only once they are consumed by an application. Thin Provisioning also allows over-provisioning of physical storage pool resources allowing ease of growth for volumes without predicting storage capacity upfront. · All models feature a wide variety of drives: High-performance SSD drives enterprise-class SAS and SAS Midline drives. · The MSA 2052 will support a maximum of 7 disk enclosures either LFF and/or SFF. Add-on enclosures can either be HPE MSA 2050 LFF Disk Enclosure or HPE MSA 2050 SFF Disk Enclosure. · The MSA 2050 can grow incrementally to a maximum of 96 LFF 192 SFF drives or a combination of SFF and LFF enclosures up to the maximum of 8 total enclosures. · Virtual Storage Disks Groups can be spanned across multiple enclosures. · Virtual Storage RAID levels supported 1 5 6 10. · Maximum hard drive counts vary by RAID levels: 2 drive max for RAID level 1 max of 16 drives for RAID levels 5 6 and 10. · Multiple Disk Groups can be aggregated into a single Storage Pool. · The maximum LUN size is 140TB 128TiB

slide 8:

Router-switch.com 7 · Storage Pools allow data on a given LUN to span across all drives in a pool. When capacity is added to a system the user is also getting a performance benefit of the additional spindles. · Snapshot enhancements for virtual storage including performance improvements hierarchical snapshots and simplified resource management. Administrators can monitor and optionally control snapshot space usage. · Prioritize data by assigning appropriate affinity level Performance No Affinity or Archive · Customers can configure 512 TiB capacity per virtual pool by enabling large pool support. · Non-disruptive on-line controller code upgrade. Requires Multi-pathing software. · Upgradable by design. Owners of an MSA 2040 MSA 2042 and MSA 1040 array are able to do data-in-place upgrades to the new MSA 2052 array. This unique ability protects the earlier investments in drives and JBODs. - Certain limitations are applicable. Please review the Upgrading to the HPE MSA 2050/2052 Technical Whitepaper before upgrading your MSA 2040 MSA 2042 or MSA 1040 systems · StoreEasy 3850 Gateway support for block and file storage. Performance MSA 2052 End-to-End Performance Results: MSA 2050 Array Performance 1 HPE MSA 2052 Converged SAN Controllers with HDDs HPE MSA 2052 Converged SAN Controllers with Mixed Use SSDs Protocol host connect 16 Gb Fibre Channel 16 Gb Fibre Channel MSA 2050 RAID 1 SSD Performance Results 2 Random Reads IOPs 220600 Random Writes IOPs 102800 MSA 2050 RAID 5 Performance Results 34 Segmented Sequential Reads MB/s 5280 Segmented Sequential Writes MB/s 4650 End-to-End performance notes 1 Performance results were generated using internal HPE test tools. Number and type of applications drive type and number of drives operating system used and the number of hosts will affect overall performance. This table is provided strictly as a test-lab comparison. 2 Dual Controller configuration 8 400GB Mixed Use SSDs RAID: 1 two drives per Disk Group two Disk Groups per Pool 2 volumes per Pool block size: 8k average latency under 5ms Windows Server 2012 host 16Gb FC direct connect to array. 3 Dual Controller configuration 72 15k HDD RAID: 5 nine drives per Disk Group 4 Disk Groups per Pool 32 volumes per Pool block size: 256k average latency under 30ms Windows Server 2012 host 16Gb FC direct connect to array. 4 Sequential performance numbers were generated using segmented sequential workloads. For segmented sequential workloads with a queue depth greater than 1 each sequential stream is targeted to operate on a separate LBA range. Other types of sequential workloads that target specific LBA ranges may achieve higher results.

slide 9:

Router-switch.com 8 End-to-End Performance Figures using Virtual Storage HPE MSA 2050 End-to-End Performance Figures 1 Controller Model HPE MSA 2050 SAN HPE MSA 2050 SAS Host Protocol 2 16 Gb FC 10 GbE iSCSI 1 GbE iSCSI 12 Gb SAS Drive Technology HDD SSD HDD SSD HDD SSD HDD SSD MSA 2050 RAID 10 Performance Results 34511 NOTE: RAID 1 was used for SSD testing. Random Reads IOPS 63600 220800 63500 208400 63200 103700 50800 219100 Random Writes IOPS 37300 103000 37300 94300 37200 93300 37100 97500 Random Mix 60/40 IOPS 47600 142100 46600 133000 46800 130500 44500 138800 Sequential Reads MB/s 5350 5350 880 5350 Sequential Writes MB/s 3110 3110 880 3120 MSA 2050 RAID 5 Performance Results 6712 Random Reads IOPS 56300 219200 55800 201400 56000 103400 47300 209600 Random Writes IOPS 18100 43400 18000 41400 18300 40600 18000 43100 Random Mix 60/40 IOPS 29100 80000 29200 75400 28700 73900 28000 78700 Sequential Reads MB/s 5290 5280 880 5290 Sequential Writes MB/s 4650 3870 880 4710 MSA 2050 RAID 6 Performance Results 891013 Random Reads IOPS 56100 219000 55700 201300 55700 105000 47400 209800 Random Writes IOPS 13000 36000 13000 35600 13200 35300 13000 36700 Random Mix 60/40 IOPS 21400 72200 21200 68500 21300 67300 21300 71500 Sequential Reads MB/s 5550 5530 880 5560 Sequential Writes MB/s 4440 3680 880 4600 NOTE: Number and type of applications drive type and number of drives operating system used and the number of hosts will affect overall performance. This table is provided strictly as a test-lab comparison. These numbers reflect a full array configuration with the maximum number of front-end ports and controllers. The test results shown for the HPE MSA 2050 are designed to give a conservative reference point for comparisons. 1. Sequential tests MB/s are based on 256K block sizes and random tests IOPS are based on 8K block sizes run against the storage. For sequential workloads with a queue depth greater than 1 each sequential stream is targeted to operate on a separate LBA range. Other types of sequential workloads that target specific LBA ranges may achieve higher results. Results cannot be expected with a single host. 2. Fibre Channel results were measured using 16 Gb FC Host Bus Adapters. SAS results were measured using 12 Gb SAS Host Bus Adapters. 10 GbE iSCSI results were measured using 10GbE iSCSI Host Bus Adapters. 1 GbE iSCSI results were measured using 1GbE network interface controllers NICs. Hosts were directly attached to the HPE MSA 2050 array. 3. MSA 2050 RAID 10 Hard Disk Drive HDD random results: Dual Controller configuration 192 15K HDD 12 drives per disk group 8 disk groups per pool 8 volumes per pool.

slide 10:

Router-switch.com 9 4. MSA 2040 RAID 10 Hard Disk Drive HDD sequential read results: Dual Controller configuration 96 15K SAS HDDs 12 drives per disk group 4 disk groups per pool 4 volumes per pool. 5. MSA 2040 RAID 10 Hard Disk Drive HDD sequential write results: Dual Controller configuration 48 15K SAS HDDs 12 drives per disk group 2 disk groups per pool 4 volumes per pool. 6. MSA 2050 RAID 5 Hard Disk Drive HDD random results: Dual Controller configuration 180 15K HDD 9 drives per disk group 10 disk groups per pool 10 volumes per pool. 7. MSA 2050 RAID 5 Hard Disk Drive HDD sequential results: Dual Controller configuration 72 15K HDD 9 drives per disk group 4 disk groups per pool 4 volumes per pool. 8. MSA 2050 RAID 6 Hard Disk Drive HDD random results: Dual Controller configuration 180 15K HDD 10 drives per disk group 9 disk groups per pool 9 volumes per pool. 9. MSA 2050 RAID 6 Hard Disk Drive HDD sequential read results: Dual Controller configuration 80 15K HDD 10 drives per disk group 4 disk groups per pool 4 volumes per pool. 10. MSA 2050 RAID 6 Hard Disk Drive HDD sequential write results: Dual Controller configuration 40 15K HDD 10 drives per disk group 2 disk groups per pool 4 volumes per pool. 11. MSA 2050 RAID 1 Solid State Drives SSD results: Dual Controller configuration 8 SSDs 2 SSDs per disk group 2 disk groups p er pool 4 volumes per pool. 12. MSA 2050 RAID 5 Solid State Drives SSD results: Dual Controller configuration 6 SSDs 3 SSDs per disk group 1 disk group per pool 4 volumes per pool. 13. MSA 2050 RAID 6 Solid State Drives SSD results: Dual Controller configuration 8 SSDs 4 SSDs per disk group 1 disk group per pool 4 volumes per pool. Technical Specifications MSA 2052 Power requirements Input Power Requirements typical-running I/O SFF/LFF arrays 110VAC 3.32A 344-390 W 220VAC 1.61A374-432W Max Input Power 100-240 VAC 50/60 Hz. 4.5-1.9A 48-60 VDC 10.4A/8.3A Heat Dissipation 1622 BTU/hr Temperature and humidity ranges Operating Temperature 41°F to 104°F 5°C to 40°C Shipping Temperature -40°F to 158°F -40°C to 70°C Operating Humidity 10 to 90 RH 104°F 40°C non-condensing Non-Operating Humidity Up to 93 RH 104°F 40°C Declared acoustic noise levels Sound Power A weighted sound power LWAd675 B

slide 11:

Router-switch.com 10 Sound Pressure A weighted sound pressure LpAm - 55dB SHOCK AND VIBRATION Shock Operational 3Gs for 11 milliseconds Shock Non-Operational 15G 11ms half sine Vibration Operational 5-500Hz 0.14 Grms shaped Vibration Non- Operational 3-365-3Hz 1.22 Grmsz-axis0.85 Grms XY axis shaped spectrum Physical Height 3.5 in/ 8.9 cm Depth excluding cables back of ear to back of controller handle SFF 24-bay array: 19.5 in / 49.5 cm LFF 12-bay array: 22.5in. / 57.2 cm Width body only 17.6 in / 44.7 cm w/ ears 19 in / 48.26 cm Weight Includes chassis and 2 controllers. No drives LFF chassis: 40.6 lbs. SFF chassis: 38.7 lbs MSA 2052 Regulatory Info Safety UL 60950-1 USA CAN/CSA-C22.2 No.60950-1-03 Canada EN 60950-1 European Union GS mark Germany IEC 60950-1 International CCC Mark power supply only China PRC Electromagnetic Compatibility VCCI:2008-04 Class A Japan FCC 15:109g Class A USA ICES-003:2004 Class A Canada EN55022: European Union Class A CISPR 22 International Class A EN61000-3- : Harmonics European Union EN61000-3-3: Flicker European Union EN 55024 European Union Immunity Class A CISPR 24 International Immunity Class A AS/NZS CISPR 22 Class A Australia New Zealand CNS 13438 Taiwan Class A Taiwan KN22 Class A Emissions Class A KN24 Immunity S Korea RoHS and WEEE RoHS-6/6 Compliance China RoHS WEEE Country Approvals United States Australia/New Zealand Canada China PRC European Union Germany GS Mark Japan South Korea Taiwan

slide 12:

Router-switch.com 11 Configuration and Order Information Step 1 - MSA 2052 - Base Configurations HPE MSA 2052 SAN Dual Controller LFF Storage Q1J02A NOTE: The MSA 2052 is a pre-configured bundle that includes an MSA 2050-branded LFF array chassis two AC power supplies two MSA 2050 SAN controllers two 800GB Mixed Use SSDs one Advanced Data Services LTU two .7m PDU cords IEC C14 and one rack-mount kit. The two 800GB SSDs are shipped integrated in the MSA 2050 array. The Advanced Data Services LTU is shipped with the MSA 2050 array and requires license activation. NOTE: SFPs not included. HPE MSA 2052 SAN Dual Controller SFF Storage Q1J03A NOTE: The MSA 2052 is a pre-configured bundle that includes an MSA 2050-branded SFF array chassis two AC power supplies two MSA 2050 SAN controllers two 800GB Mixed Use SSDs one Advanced Data Services LTU two .7m PDU cords IEC C14 and one rack-mount kit. The two 800GB SSDs are shipped integrated in the MSA 2050 array. The Advanced Data Services LTU is shipped with the MSA 2050 array and requires license activation. NOTE: SFPs not included. HPE MSA 2052 SAS Dual Controller LFF Storage Q1J30A NOTE: The MSA 2052 is a pre-configured bundle that includes an MSA 2050-branded LFF array chassis two AC power supplies two MSA 2050 SAS controllers two 800GB Mixed Use SSDs one Advanced Data Services LTU two .7m PDU cords IEC C14 and one rack-mount kit. The two 800GB SSDs are shipped integrated in the MSA 2050 array. The Advanced Data Services LTU is shipped with the MSA 2050 array and requires license activation. NOTE: SFPs are not required for SAS Storage systems. HPE MSA 2052 SAS Dual Controller SFF Storage Q1J31A NOTE: The MSA 2052 is a pre-configured bundle that includes an MSA 2050-branded SFF array chassis two AC power supplies two MSA 2050 SAS controllers two 800GB Mixed Use SSDs one Advanced Data Services LTU two .7m PDU cords IEC C14 and one rack-mount kit. The two 800GB SSDs are shipped integrated in the MSA 2050 array. The Advanced Data Services LTU is shipped with the MSA 2050 array and requires license activation. NOTE: SFPs are not required for SAS Storage systems. Step 2 – Choose Your SFP+ Module SFP+ Modules HPE MSA 8Gb Short Wave Fibre Channel SFP+ 4-pack Transceiver Includes four x 8Gb SW FC SFPs C8R23B HPE MSA 16Gb Short Wave Fibre Channel SFP+ 4-pack Transceiver Includes four x 16Gb SW FC SFPs C8R24B HPE MSA 10Gb Short Range iSCSI SFP+ 4-pack Transceiver Includes four x 10Gb SW iSCSI SFPs C8R25B HPE MSA 1Gb RJ-45 iSCSI SFP+ 4-pack Transceiver Includes four x 1Gb RJ-45 iSCSI SFPs C8S75B

slide 13:

Router-switch.com 12 Step 3 – Select Your Drives MSA HDDs and SSDs drives are for use with MSA Storage Systems only. Customers can mix SSD SAS and SAS MDL drives in the same array enclosure and disk enclosure SFF SSDs 12G SFF SAS SSDs Mixed Use HPE MSA 400GB 12G SAS Mixed Use SFF 2.5in 3yr Warranty Solid State Drive N9X95A HPE MSA 800GB 12G SAS Mixed Use SFF 2.5in 3yr Warranty Solid State Drive N9X96A HPE MSA 1.6TB 12G SAS Mixed Use SFF 2.5in 3yr Warranty Solid State Drive N9X91A HPE MSA 3.2TB 12G SAS Mixed Use SFF 2.5in 3yr Warranty Solid State Drive N9X92A SFF HDDs 12G SFF 15K SAS HDDs HP MSA 300GB 12G SAS 15K SFF 2.5in Enterprise 3yr Warranty Hard Drive J9F40A HP MSA 600GB 12G SAS 15K SFF 2.5in Enterprise 3yr Warranty Hard Drive J9F42A HPE MSA 900GB 12G SAS 15K SFF 2.5in Enterprise 3yr Warranty Hard Drive Q1H47A 12G SFF 10K SAS HDDs HP MSA 300GB 12G SAS 10K SFF2.5in Dual Port Enterprise 3yr Warranty Hard Drive J9F44A HP MSA 600GB 12G SAS 10K SFF2.5in Dual Port Enterprise 3yr Warranty Hard Drive J9F46A HP MSA 1.2TB 12G SAS 10K SFF2.5in Dual Port Enterprise 3yr Warranty Hard Drive J9F48A HP MSA 1.8TB 12G SAS 10K SFF 2.5in 512e Enterprise 3yr Warranty Hard Drive J9F49A NOTE: 512e drives require MSA 1040/2040 firmware version GL200P002 or newer 12G SFF 7.2K SAS MDL HDDs HP MSA 1TB 12G SAS 7.2K SFF 2.5in 512e Midline 1yr Warranty Hard Drive J9F50A HP MSA 2TB 12G SAS 7.2K SFF 2.5in 512e Midline 1yr Warranty Hard Drive J9F51A NOTE: 512e drives require MSA 1040/2040 firmware version GL200P002 or newer LFF SSDs 12G LFF SAS SSDs Mixed Use HPE MSA 400GB 12G SAS Mixed Use LFF 3.5in Converter Carrier 3yr Wty Solid State Drive P9M79A HPE MSA 800GB 12G SAS Mixed Use LFF 3.5in Converter Carrier 3yr Wty Solid State Drive P9M80A LFF HDDs 12G LFF 7.2K SAS Midline Drives HPE MSA 2TB 12G SAS 7.2K LFF 3.5in 512n Midline 1 yr Warranty Hard Drive N9X93A HPE MSA 4TB 12G SAS 7.2K LFF 3.5in 512e Midline 1yr Warranty Hard Drive K2Q82A HPE MSA 6TB 12G SAS 7.2K LFF 3.5in 512e Midline 1yr Warranty Hard Drive J9F43A HPE MSA 8TB 12G SAS 7.2K LFF 3.5in 512e Midline 1yr Warranty Hard Drive M0S90A HPE MSA 10TB 12G SAS 7.2K LFF 3.5in Midline 512e 1 yr Wty Hard Drive P9M82A HPE MSA 12TB 12G SAS 7.2K LFF 3.5in Midline 512e 1yr Warranty Hard Drive Q2R42A SFF SEDs

slide 14:

Router-switch.com 13 MSA Small Form Factor SFF SAS DP Self-Encrypted Drives HPE MSA 1.2TB 12G SAS 10K SFF 2.5in Enterprise Self Encrypted 3yr Wty Hard Drive P9M81A LFF SED MSA Large Form Factor LFF SAS DP Self-Encrypted Drives HPE MSA 4TB 12G SAS 7.2K LFF 3.5in Enterprise Self Encrypted 3 yr Wty Hard Q1H48A Step 4 – Options Drive Enclosures HPE MSA 2050 LFF Disk Enclosure Q1J06A HPE MSA 2050 SFF Disk Enclosure Note : · Each drive enclosure includes two 0.5m MiniSAS to MiniSAS cables · Add up to 7 additional drive enclosures · MSA 2050 LFF Disk Enclosure can be connected to either the MSA 2050 SFF or LFF dual controller systems. · HPE MSA 2050 SFF Disk Enclosure can be connected to either the MSA 2050 SFF or LFF dual controller systems. Q1J07A SAS Cable HP External Mini SAS 1m Cable ALL 407337-B21 HP External Mini SAS 2m Cable 407339-B21 Power Cords HPE C13 - C14 WW 250V 10Amp 2.0m Jumper Cord A0K02A HPE C13 - C14 WW 250V 10Amp Flint Gray 2.0m Jumper Cord AF573A HPE C13 - AS3112-3 AU 250V 10Amp 2.5m Power Cord AF569A HPE C13 - BS-1363A UK/HK/SG 250V 10Amp 1.83m Power Cord AF570A HPE C13 - C14 WW 250V 10A Gray 0.7m Jumper Cord A0K03A HPE C13 - C14 WW 250V 10A Gray 1.37m Jumper Cord A0K04A HPE C13 - CEE-VII EU 250V 10Amp 1.83m Power Cord AF568A HPE C13 - CEI-23-50 IT/CL 250V 10Amp 1.83m Power Cord AF571A HPE C13 - CNS-690 TW 110V 13Amp 1.83m Power Cord AF561A HPE C13 - DK-2.5A DK 250V 10Amp 1.83m Power Cord AF566A HPE C13 - GB-1002 CN 250V 10Amp 1.83m Power Cord AF557A HPE C13 - IRAM -2073 AR 250V 10A 2.5m Power Cord AF558A HPE C13 - IS-1293 IN 240V 6Amp LV 2.0m Power Cord AF562A HPE C13 - JIS C8303 JP 100V 12Amp 2.0m Power Cord AF572A HPE C13 - KSC- 8305 KR 250V 10Amp 1.83m Power Cord AF560A HPE C13 - NBR-14136 BR 250V 10Amp 1.83m Power Cord AF591A HPE C13 - Nema 5-15P US/CA 110V 10Amp 1.83m Power Cord AF556A HPE C13 - SABS-164 ZA 250V 10Amp 2.5m Power Cord AF567A HPE C13 - SEV 1011 CH 250V 10Amp 1.83m Power Cord AF565A HPE C13 - SI-32 IL 250V 10Amp 1.83m Power Cord AF564A HPE C13-NEMA 6-15P 10A/250V 3.6m Black Power Cord A0N33A HPE OEM C13 - C14 WW 250V 10A Gray 3m Jumper Cord A0K06A

slide 15:

Router-switch.com 14 NOTE: · Two PDU cables: one 142263-008 Black and one 1422633-013 Grey ship standard with all AC-powered enclosures. Step 5a - Choose Supported Options for Fibre Channel Infrastructure PremierFlexOM4 type cables HP Premier Flex LC/LC Multi-mode OM4 2 fiber 5m Cable QK734A HP Premier Flex LC/LC Multi-mode OM4 2 fiber 15m Cable QK735A HP Premier Flex LC/LC Multi-mode OM4 2 fiber 30m Cable QK736A HP Premier Flex LC/LC Multi-mode OM4 2 fiber 50m Cable QK737A HP LC to LC Multi-mode OM3 2-Fiber 0.5m 1-Pack Fiber Optic Cable AJ833A HP LC to LC Multi-mode OM3 2-Fiber 1.0m 1-Pack Fiber Optic Cable AJ834A HPE LC to LC Multi-mode OM3 2-Fiber 2.0m 1-Pack Fiber Optic Cable AJ835A OM3 FC LC-LC cables HP LC to LC Multi-mode OM3 2-Fiber 5.0m 1-Pack Fiber Optic Cable AJ836A HP LC to LC Multi-mode OM3 2-Fiber 15.0m 1-Pack Fiber Optic Cable AJ837A HP LC to LC Multi-mode OM3 2-Fiber 30.0m 1-Pack Fiber Optic Cable AJ838A HP LC to LC Multi-mode OM3 2-Fiber 50.0m 1-Pack Fiber Optic Cable AJ839A Step 5b - Choose Supported Options For 10GbE Infrastructure Mini SAS Cables HPE 1.0m External Mini SAS High Density to Mini SAS Cable 716189-B21 HPE 2.0m External Mini SAS High Density to Mini SAS Cable 716191-B21 NOTE: These cables are used to connect 6Gb SAS initiator to MSA 2050 SAS controller. These are not used for connecting to a disk enclosure. HPE External 1.0m 3ft Mini-SAS HD 4x to Mini-SAS HD 4x Cable 716195-B21 HPE External 2.0m 6ft Mini-SAS HD 4x to Mini-SAS HD 4x Cable 716197-B21 NOTE: These cables are used to connect 12Gb SAS initiator to MSA 2050 SAS controller. These are not used for connecting to a disk enclosure. HPE 4.0m External Mini SAS High Density to Mini SAS Cable 716193-B21 NOTE: This cable is used to connect 6Gb SAS initiator to MSA 2050 SAS controller. This is not used for connecting to a disk enclosure. HPE External 4.0m 13ft Mini-SAS HD 4x to Mini-SAS HD 4x Cable 716199-B21 NOTE: These cables are used to connect 12Gb SAS initiator to MSA 2050 SAS controller. These are not used for connecting to a disk enclosure SAS Controllers/HBAs HPE Smart Array E208e-p SR Gen10 8 External Lanes/No Cache 12G SAS PCIe Plug-in Controller 804398-B21 HPE Smart Array P408e-p SR Gen10 8 External Lanes/4GB Cache 12G SAS PCIe Plug-in Controller 804405-B21 HPE Smart Array P408e-m SR Gen10 8 External Lanes/2GB Cache 12G SAS Mezzanine Controller 804381-B21 HPE H241 12Gb 2-ports Ext Smart Host Bus Adapter 726911-B21 HPE Smart Array P441/4GB FBWC 12Gb 2-ports Ext SAS Controller 726825-B21

slide 16:

Router-switch.com 15 SAS Switches HPE 6Gb SAS Switch Single Pack for HPE BladeSystem c-Class BK763A HPE 6Gb SAS Switch Dual Pack for HPE BladeSystem c-Class BK764A Step 6 – Software The MSA Advanced Data Services Software Suite comes standard on the MSA 2052. No optional software titles are available on the MSA 2052. Step 7 – Add File Services HPE Storage File Controller Q9D43A NOTE: HPE Storage File Controllers have 4 x 1GbE ports and are pre-configured with Windows Storage Server 2016 which includes a software iSCSI initiator. Other connections require adding an HBA or adapter. Cluster up to eight file controllers for high availability and with transparent failover enabling continuity of data access in the event of a failure. Where to Buy Want to buy this series of products please contact: ● Tel: +1-626-239-8066 USA/ +852-3050-1066 / +852-3174-6166 ● Fax: +852-3050-1066 Hong Kong ● Email: salesrouter-switch.com Sales Inquiries Or visit: HPE MSA Storage Controllers About us Router-switch.com founded in 2002 is one of the biggest Global Network Hardware Supplier. We are a leading provider of network products with 14500+ customers in over 200 countries. We provide original new and used network equipments Cisco Huawei HPE Dell Juniper EMC etc. including Routers Switches Servers Storage Telepresence and Videoconferencing IP Phones Firewalls Wireless APs Controllers EHWIC/HWIC/VWIC Cards SFPs Memory Flash Hard Disk Cables and all kinds of network solutions related products. Source https://h20195.www2.hpe.com/v2/gethtml.aspxdocnamea00008277enw

authorStream Live Help