2019 Millings Rejevenated with HS-E Blend Presentation 3d

Views:
 
Category: Others/ Misc
     
 

Presentation Description

This tutorial will demonstrate how to solve the two most common complaints of using millings for driveways, parking lots and streets which is the tracking of fines and washing or erosion of the millings, and share tips on building a solid durable smooth roadway.

Comments

Presentation Transcript

Slide1:

Hawk Seale-MB “Millings Blend” for Asphalt Millings http://hawkseale.com

Slide2:

In this tutorial we will share construction tips on using Millings for driveways, parking lots and streets. Also we will share how rejuvenating asphalt millings with Hawk Seale-E Blend will eliminate erosion problems and also raveling and the tracking of fines into vehicles, garages and homes which are the two most common complaints.

Slide3:

Re-cycled Millings have become a popular economical alternative to “HOT mix” asphalt and concrete. However, getting a smooth non-erodible, smooth non-raveling, non-tracking surface has been a challenge which are the two most common complaints of using millings.

Slide4:

An advantage of using millings is they don’t require large equipment. These millings were placed and treated with Hawk Seale-E Blend to create a smooth an durable surface that will not erode or track.

Slide5:

Asphalt Millings Asphalt Millings are a popular alternative to HOT Asphalt and concrete for parking lots, driveways and roads. Millings do not require expensive equipment to lay, but do require attention to site preparation. Millings have no structural strength of their own and rely on a solid base. Existing roads can provide the necessary base. For new projects we recommend 4 to 6 inches of 2” rock be laid and compacted for the base Good drainage is also very important

Slide6:

Course or rough millings can be used for base Screened or ground millings are preferred for a smooth finish. We recommend 4 to 5 inches of screened millings You want enough millings depth to prevent the grading and leveling and the incorporation of Hawk Seale-E Blend from bringing up gravel or dirt.

Slide7:

Asphalt Millings An experienced driver can gate spread the millings This will reduce much of the labor in placing and grading the millings. There is usually no charge for spreading the millings

Slide8:

A good driver can tail gate spread your millings eliminating a lot of time and labor to prepare your project.

Slide9:

A disadvantage of Raw Millings is they tend to ravel and the “fines” tend to track into vehicles, garages and buildings; areas where they are not wanted and are also subject to erosion.

Slide10:

Incorporating “Hawk Seale-E Blend” into the millings rejuvenates and softens the asphalt in the millings; then HS-E Blends co-polymers and binders help create a smoother and more durable surface.

Slide11:

Hawk Seale-MB (Millings Blend) Non Hazardous Safe for the environment Contains a proprietary blend of acid, co-polymers and binder that rejuvenates the asphalt and re-binds the agregate in the millings. Incorporating Hawk Seale Millings MB will create a tight durable water proof surface and reduce raveling, erosion and tracking..

Slide12:

Various equipment can be used to incorporate Hawk Seale-E Blend solution into the top 2 to 3 inches of the millings. Asphalt Pavers and power rakes can be also be used. However we like low maintenance equipment

Slide13:

We use this pulverizer machine as it is designed to work up the surface and is low maintenance and works very well to incorporate the solution into the top 2 to 3 inches of the millings

Slide14:

We recommend a minimum of 4 to 5 inches of millings to prevent pulling up any rocks or dirt when grading and leveling the millings or when incorporating the HS-E solution into the millings.

Slide15:

Incorporating a total of 1 gallon of HS-E Blend solution in 3 separate passes will provide maximum saturation and penetration. When treating millings that have been previously laid and compacted they typically will not absorb more than .8 tenths of a gallon per square yard before puddleing and or running off. Incorporating provides a deeper more durable surface for ag equipment and 4 wheelers.

Slide16:

This is the 3 rd and final pass, notice the solution is beginning to puddle, the millings at this point and will become like a slurry similar to poured concrete.

Slide17:

A simple boom set up can be constructed with a Water Trash Pump and PVC. 80-50 Fan Jet nozzles were spaced every 12 inches. A valve in the line controls amount of solution going back to the tank also controls the pressure to the boom. A Tee and Valve could be added to feed a hose and wand if desired. Final application of 1.0 gallon per square yard is done, now to wait 45 minutes to an hour for the solution to soften and rejuvenate the asphalt in the millings before compacting the millings.

Slide18:

A simple boom set up can be constructed with a Water Trash Pump and PVC. 80-50 Fan Jet nozzles were spaced every 12 inches. A valve in the line controls amount of solution going back to the tank also controls the pressure to the boom. A Tee and Valve could be added to feed a hose and wand if desired. Once the HS-E Blend has set up enough to carry the weight of the roller without rippling ahead of the roller we recommend compacting the millings several times in first 24 hours.

Slide19:

The finished Hawk Seale rejuvenated surface, you will notice a carpet like feel until the treated millings have fully cured, typically in 7 to 14 days depending on temperature.

Slide20:

Light traffic such as cars and pickups can begin immediately. Over night parking and heavy garbage trucks and farm tractors with aggressive tires should be avoided until the treated millings have fully cured.

Slide23:

A simple boom set up can be constructed with a Water Trash Pump and PVC. 80-50 Fan Jet nozzles were spaced every 12 inches. A valve in the line controls amount of solution going back to the tank also controls the pressure to the boom. A Tee and Valve could be added to feed a hose and wand if desired.

Slide24:

A simple boom set up can be constructed with a Water Trash Pump and PVC. 80-50 Fan Jet nozzles were spaced every 12 inches. A valve in the line controls amount of solution going back to the tank also controls the pressure to the boom. A Tee and Valve could be added to feed a hose and wand if desired.

Slide25:

A simple boom set up can be constructed with a Water Trash Pump and PVC. 80-50 Fan Jet nozzles were spaced every 12 inches. A valve in the line controls amount of solution going back to the tank also controls the pressure to the boom. A Tee and Valve could be added to feed a hose and wand if desired.

Slide26:

Here a wand is being used to saturate the millings on a smaller project. Tanks or drums can be mounted on trucks or trailers. Sprinkle cans can be used for very small projects.

Slide27:

Once the treated millings have had sufficient time to set up to prevent running and rippling of the millings ahead of the roller, we recommend compacting the millings several times in the first 24 hours.

Slide28:

The shoulders should be back filled to support the millings to prevent them from sloughing off. Also remember good drainage is also important .

Slide29:

The completed smooth and durable road will not erode or track. The cost will be between ½ and 2/3’s the cost of “HOT” asphalt.

Slide30:

Hawk Seale Distributing LLC Our Website- http://hawkseale.com Email us at- hawkseale@gmail.com Or visit our Face Book page at Hawk Seale Distributing LLC Dealers inquiries are welcome.

authorStream Live Help