ssp 020 Common_Rail

Views:
 
Category: Entertainment
     
 

Presentation Description

No description available.

Comments

Presentation Transcript

COMMON RAIL FUEL INJECTION SYSTEM:

COMMON RAIL FUEL INJECTION SYSTEM ;JL";L\U V[g0 VMJZ CM,L\U VMO VM8MDMAF., s 0Lh, f] ,[XG G\AZ : 15

Demand On Modern Diesel Engine Development :

Demand On Modern Diesel Engine Development Low fuel consumption Low pollutant emissions Quiet running engines Improved engine performance

Common rail fuel injection system and its function:

Common rail fuel injection system and its function Provide the diesel engine with fuel Generate the high pressure needed for fuel injection and distribute the fuel to the individual cylinders Inject precisely correct amount of fuel at exactly the right moment in time. In contrast to other injection system Common rail fuel injection system is an accumulator injection system.

How does a CR system function?:

How does a CR system function?

The Common Rail Sub functions:

Low –pressure circuit comprises of: Fuel tank ,Pre-supply pump, Fuel filter, And the respective connection lines. The Common Rail Sub functions

Low –pressure circuit:

Low –pressure circuit The low –pressure circuit is responsible for transporting the fuel to the high –pressure circuit

The Common Rail Sub functions:

High –pressure circuit comprises: High – pressure pump with pressure – control valve The high – pressure accumulator (Rail )with the rail –pressure sensor Injectors, and The respective high – pressure connection lines. The Common Rail Sub functions

The high – pressure circuit:

The high – pressure circuit It is the responsibility of the high pressure circuit to generate a constant unvarying high pressure in the high pressure accumulator (the rail) and to inject the fuel through the injectors into the engine’s combustion chambers.

The Common Rail Sub functions:

ECU and sensors The common rail ECU evaluates the signals from the following sensors. Crankshaft – speed sensor, Camshaft sensor, Accelerator-pedal travel sensor The Common Rail Sub functions

The Common Rail Sub functions:

The common rail ECU evaluates the signals from the following sensors: Boost – pressure sensor, Air temperature sensor, Air – mass meter, and Rail pressure sensor. The Common Rail Sub functions

The Common Rail Sub functions:

The Common Rail Sub functions ECU and sensors The sensor are responsible for measuring important physical quantities. The ECU calculates injected fuel quantity, start of injection, duration of injection, and rate of discharge curve, as well supervises the correct functioning of the injection system as a whole.

COMMON RAIL FUEL INJECTION SYSTEM DESIGN:

PRE SUPPLY PUMP Transports fuel from the fuel tank to the high pressure pump. An electric fuel pump is used for this purpose in the CRFIS. When the electric fuel pump is switched off, the supply of fuel is interrupted and the engine stops. COMMON RAIL FUEL INJECTION SYSTEM DESIGN

PRE SUPPLY PUMP:

PRE SUPPLY PUMP The electric fuel pump comprises of: 1.Electric Motor 2.Roller-Cell Pump 3.Non Return Valve

PRE SUPPLY PUMP:

The roller cell is driven by an electric motor. Its rotor is mounted eccentrically and provided with slots in which movable rollers are free to travel. PRE SUPPLY PUMP

PRE SUPPLY PUMP:

The rollers are forced against the base plate by rotation and by fuel pressure . The fuel is transported to the outlet openings on the pump’s pressure side. PRE SUPPLY PUMP

PRE SUPPLY PUMP variants:

Gear type fuel pump The drive gear wheel is driven by the engine . Delivery quantity is directly proportional to engine speed . Shut off is by means of an electromagnet.. PRE SUPPLY PUMP variants

High- pressure pump :

High- pressure pump The pump plunger moves downwards The inlet valve opens The fuel is drawn in to the pumping element chamber(suction stroke)

High- pressure pump :

At BDC, the inlet valve closes The fuel in the chamber can be compressed by the upward moving plunger. High- pressure pump

High- pressure pump :

An electromagnet is used for pumping element switch-off. High- pressure pump

High- pressure accumulator (Rail):

High- pressure accumulator (Rail) Store fuel Prevent pressure fluctuations

High- pressure accumulator (Rail):

Rail is a forged-steel tube. ID is approx.. 10mm Length is between 280 and 600mm The volume must be “ as small as possible, as large as necessary” High- pressure accumulator (Rail)

Pressure-control valve (DRV):

Pressure-control valve (DRV) Responsible for maintaining the pressure in the rail at a constant level.

Rail-pressure sensor (RDS) :

Rail-pressure sensor (RDS) Measures the pressure in the rail inputs the information to the ECU RDS should provide extremely precise measured values. RDS is mounted directly on the rail.

Injector :

Injector Injects exactly the correct amount of fuel in to the combustion chamber at precisely the right moment in time

Injector:

The injector is equipped with: 2/2 electromagnetic servo valve Nozzle Valve control chamber Return line Injector

Injector :

The essential forces for correct functioning are: Nozzle-spring force Valve spring force Electromagnet force Force due to the pressure in the valve-control chamber Force due to the pressure in the nozzle needle Injector

ECU with sensors :

ECU with sensors Common Rail is an EDC controlled injection system The ECU controls & monitors the complete injection process The sensors delivers all the measured values which are required in the process

COMMON RAIL FUEL INJECTION SYSTEM:

Summary Components of CRFIS are: Pre-supply pump High-pressure pump High-pressure accumulator(rail) Pressure-control valve Rail-pressure sensor Injectors ECU with sensors COMMON RAIL FUEL INJECTION SYSTEM

COMMON RAIL FUEL INJECTION SYSTEM:

COMMON RAIL FUEL INJECTION SYSTEM SUMMAR 1.The basic functional groups of the common rail are : low – pressure circuit , high – pressure circuit ECU and sensors. 2.In the low – pressure circuit, the fuel is cleaned by a filter and then transported to the high – pressure circuit COMMON RAIL FUEL INJECTION SYSTEM

PowerPoint Presentation:

SUMMARY 3.In the high – pressure circuit , the maximum pressure of 1,350 bar is generated in the high – pressure accumulator (Rail). The pressure is maintained at a constant level , and the fuel is taken from the rail every time an injection takes place. 4.The ECU controls and monitors the complete injection system. Using the signals from the sensors, the ECU calculates all the values for the injection process and triggers the components in high-pressure circuit (pressure – control valve, injectors).

authorStream Live Help